ISO pipe standards
ISO pipe standards
| Standards | Application |
|---|---|
| IEC 60794-3-10-2002 |
Optical fibre cables - Part 3-10: Outdoor cables; Family specification for duct and directly buried optical telecommunication cables |
| IEC 60794-3-12-2005 |
Optical fibre cables - Part 3-12: Outdoor cables - Detailed specification for duct and directly buried optical telecommunication cables for use in premises cabling |
| IEC 61084-1 AMD 1-1993 |
Cable trunking and ducting systems for electrical installations; part 1: general requirements; amendment 1 |
| IEC 61084-1-1991 |
Cable trunking and ducting systems for electrical installations; part 1: general requirements |
| IEC 61084-2-1-1996 |
Cable trunking and ducting systems for electrical installations - Part 2: Particular requirements - Section 1: Cable trunking and ducting systems intended for mounting on walls or ceilings |
| IEC 61084-2-2-2003 |
Cable trunking and ducting systems for electrical installations - Part 2-2: Particular requirements; Cable trunking systems and cable ducting systems intended for underfloor and flushfloor installations |
| IEC 61084-2-4-1996 |
Cable trunking and ducting systems for electrical installations - Part 2: Particular requirements - Section 4: Service poles |
| IEC 61400-21-2001 |
Wind turbine generator systems - Part 21: Measurement and assessment of power quality characteristics of grid connected wind turbines |
| ISO 10380-2003 |
Pipework - Corrugated metal hoses and hose assemblies |
| ISO 10466-1997 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method to prove the resistance to initial ring deflection |
| ISO 10467-2004 |
Plastics piping systems for pressure and non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin |
| ISO 10472-3-1997 |
Safety requirements for industrial laundry machinery - Part 3: Washing tunnel lines including component machines |
| ISO 10508-2006 |
Plastics piping systems for hot and cold water installations - Guidance for classification and design |
| ISO 10639-2004 |
Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin |
| ISO 10790-1999 |
Measurement of fluid flow in closed conduits - Guidance to the selection, installation and use of Coriolis meters (mass flow, density and volume flow measurements) |
| ISO 10802-1992 |
Ductile iron pipelines; hydrostatic testing after installation |
| ISO 10804-1-1996 |
Restrained joint systems for ductile iron pipelines - Part 1: Design rules and type testing |
| ISO 10806-2003 |
Pipework - Fittings for corrugated metal hoses |
| ISO 10807-1994 |
Pipework - Corrugated flexible metallic hose assemblies for the protection of electrical cables in explosive atmospheres |
| ISO 10838-1-2000 |
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels - Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm |
| ISO 10838-2-2000 |
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels - Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm |
| ISO 10838-3-2001 |
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels - Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm |
| ISO 10928-1997 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Methods for regression analysis and their use |
| ISO 10931-2005 |
Plastics piping systems for industrial applications - Poly(vinylidene fluoride) (PVDF) - Specifications for components and the system |
| ISO 10952-1999 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Determination of the resistance to chemical attack from the inside of a section in a deflected condition |
| ISO 11563-2003 |
Crude petroleum and petroleum products - Bulk cargo transfer - Guidelines for achieving the fullness of pipelines |
| ISO 11691-1995 |
Acoustics - Measurement of insertion loss of ducted silencers without flow - Laboratory survey method |
| ISO 13253-1995 |
Ducted air-conditioners and air-to-air heat pumps - Testing and rating for performance |
| ISO 13261-1-1998 |
Sound power rating of air-conditioning and air-source heat pump equipment - Part 1: Non-ducted outdoor equipment |
| ISO 13261-2-1998 |
Sound power rating of air-conditioning and air-source heat pump equipment - Part 2: Non-ducted indoor equipment |
| ISO 13359-1998 |
Measurement of conductive liquid flow in closed conduits - Flanged electromagnetic flowmeters - Overall length |
| ISO 13623-2000 |
Petroleum and natural gas industries - Pipeline transportation systems |
| ISO 13628-5-2002 |
Petroleum and natural gas industries - Design and operation of subsea production systems - Part 5: Subsea umbilicals |
| ISO 13678 Technical Corrigendum 1-2005 |
Petroleum and natural gas industries - Evaluation and testing of thread compounds for use with casing, tubing and line pipe; Technical Corrigendum 1 |
| ISO 13678-2000 |
Petroleum and natural gas industries - Evaluation and testing of thread compounds for use with casing, tubing and line pipe |
| ISO 13703 Technical Corrigendum 1-2002 |
Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms; Technical Corrigendum 1 |
| ISO 13703-2000 |
Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms |
| ISO 13761-1996 |
Plastics pipes and fittings - Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 C |
| ISO 13783-1997 |
Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double-socket joints - Test method for leaktightness and strength while subjected to bending and internal pressure |
| ISO 13844-2000 |
Plastics piping systems - Elastomeric-sealing-ring-type socket joints of unplasticized poly(vinyl chloride) (PVC-U) for use with PVC-U pipes - Test method for leaktightness under negative pressure |
| ISO 13845-2000 |
Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for leaktightness under internal pressure and with angular deflection |
| ISO 13846-2000 |
Plastics piping systems - End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping - Test method for long-term leaklightness under internal water pressure |
| ISO 13847 Technical Corrigendum 1-2001 |
Petroleum and natural gas industries - Pipeline transportation systems - Welding of pipelines; Technical Corrigendum 1 |
| ISO 13847-2000 |
Petroleum and natural gas industrie - Pipeline transportation systems - Welding of pipelines |
| ISO 13951-2001 |
Plastics piping systems - Test method for the resistance of polyolefin pipe/pipe or pipe/fitting assemblies to tensile loading |
| ISO 13968-1997 |
Plastics piping and ducting systems - Thermoplastics pipes - Determination of ring flexibility |
| ISO 14164-1999 |
Stationary source emissions - Determination of the volume flowrate of gas streams in ducts - Automated method |
| ISO 14313-1999 |
Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves |
| ISO 14511-2001 |
Measurement of fluid flow in closed conduits - Thermal mass flowmeters |
| ISO 14531-1-2002 |
Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels; Metric series; Specifications - Part 1: Pipes |
| ISO 14531-2-2004 |
Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Part 2: Fittings for heat-fusion jointing |
| ISO 14531-3-2006 |
Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Part 3: Fittings for mechanical jointing (including PE-X/metal transitions) |
| ISO 14531-4-2006 |
Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Part 4: System design and installation guidelines |
| ISO 14692-3-2002 |
Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System piping |
| ISO 14723-2001 |
Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves |
| ISO 14726-2-2002 |
Ships and marine technology - Identification colours for the content of piping systems - Part 2: Additional colours for different media and/or functions |
| ISO 15002-2000 |
Flow-metering devices for connection to terminal units of medical gas pipeline systems |
| ISO 15306-2003 |
Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the resistance to cyclic internal pressure |
| ISO 15348-2002 |
Pipework - Metal bellows expansion joints - General |
| ISO 15465-2004 |
Pipework - Stripwound metal hoses and hose assemblies |
| ISO 15493 Technical Corrigendum 1-2004 |
Plastics piping systems for industrial applications - Acrylonitrile-butadiene-styrene (ABS), unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) - Specifications for components and the system - Metric series; Technical Corrigendum 1 |
| ISO 15493-2003 |
Plastics piping systems for industrial applications - Acrylonitrile-butadiene-styrene (ABS), unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) - Specifications for components and piping systems; Metric series |
| ISO 15494-2003 |
Plastics piping systems for industrial applications - Polybutene (PB), polyethylene (PE) and polypropylene (PP) - Specifications for components and the systems; Metric series |
| ISO 15589-1-2003 |
Petroleum and natural gas industries - Cathodic protection of pipeline transportation systems - Part 1: On-land pipelines |
| ISO 15589-2-2004 |
Petroleum and natural gas industries - Cathodic protection of pipeline transportation systems - Part 2: Offshore pipelines |
| ISO 15590-1-2001 |
Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends |
| ISO 15590-2-2003 |
Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 2: Fittings |
| ISO 15590-3-2004 |
Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 3: Flanges |
| ISO 15649-2001 |
Petroleum and natural gas industries - Piping |
| ISO 15665 Technical Corrigendum 1-2004 |
Acoustics - Acoustic insulation for pipes, valves and flanges; Technical Corrigendum 1 |
| ISO 15749-2-2004 |
Ships and marine technology - Drainage systems on ships and marine structures - Part 2: Sanitary drainage, drain piping for gravity systems |
| ISO 15749-3-2004 |
Ships and marine technology - Drainage systems on ships and marine structures - Part 3: Sanitary drainage, drain piping for vacuum systems |
| ISO 15837-2004 |
Ships and marine technology - Gasketed mechanical couplings for use in piping systems - Performance specification |
| ISO 15838-2003 |
Ships and marine technology - Fittings for use with gasketed mechanical couplings used in piping applications - Performance specification |
| ISO 15840-2004 |
Ships and marine technology - Standard specification for thermosetting resin fibreglass pipe and fittings to be used for marine applications |
| ISO 15874-1-2003 |
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General |
| ISO 15874-2-2003 |
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes |
| ISO 15874-3-2003 |
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings |
| ISO 15874-5-2003 |
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 5: Fitness for purpose of the system |
| ISO 15875-1-2003 |
Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 1: General |
| ISO 15875-2-2003 |
Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 2: Pipes |
| ISO 15875-3-2003 |
Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings |
| ISO 15875-5-2003 |
Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system |
| ISO 15876-1-2003 |
Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 1: General |
| ISO 15876-2-2003 |
Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 2: Pipes |
| ISO 15876-3-2003 |
Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 3: Fittings |
| ISO 15876-5-2003 |
Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 5: Fitness for purpose of the system |
| ISO 15877-1-2003 |
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: General |
| ISO 15877-2-2003 |
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes |
| ISO 15877-3-2003 |
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings |
| ISO 15877-5-2003 |
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system |
| ISO 15908-2002 |
Adhesives for thermoplastic piping systems - Test method for the determination of thermal stability of adhesives |
| ISO 16422-2006 |
Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure - Specifications |
| ISO 16708-2006 |
Petroleum and natural gas industries - Pipeline transportation systems - Reliability-based limit state methods |
| ISO 16871-2003 |
Plastics piping and ducting systems - Plastics pipes and fittings - Method for exposure to direct (natural) weathering |
| ISO 17454-2006 |
Plastics piping systems - Multilayer pipes - Test method for the adhesion of the different layers using a pulling rig |
| ISO 17455-2005 |
Plastics piping systems - Multilayer pipes - Determination of the oxygen permeability of the barrier pipe |
| ISO 19220-2004 |
Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Styrene copolymer blends (SAN + PVC) |
| ISO 19921-2005 |
Ships and marine technology - Fire resistance of metallic pipe components with resilient and elastomeric seals - Test methods |
| ISO 19922-2005 |
Ships and marine technology - Fire resistance of metallic pipe components with resilient and elastomeric seals - Requirements imposed on the test bench |
| ISO 21329-2004 |
Petroleum and natural gas industries - Pipeline transportation systems - Test procedures for mechanical connectors |
| ISO 2186-1973 |
Fluid flow in closed conduits; Connections for pressure signal transmissions between primary and secondary elements |
| ISO 24033-2006 |
Pipes made of raised-temperature-resistance polyethylene (PE-RT) - Effect of time and temperature on the expected strength |
| ISO 2975-1-1974 |
Measurement of water flow in closed conduits; Tracer methods; Part I : General |
| ISO 2975-2-1975 |
Measurement of water flow in closed conduits; Tracer methods; Part II : Constant rate injection method using non-radioactive tracers |
| ISO 2975-3-1976 |
Measurement of water flow in closed conduits; Tracer methods; Part III : Constant rate injection method using radioactive tracers |
| ISO 2975-6-1977 |
Measurement of water flow in closed conduits; Tracer methods; Part VI : Transit time method using non-radioactive tracers |
| ISO 2975-7-1977 |
Measurement of water flow in closed conduits; Tracer methods; Part VII : Transit time method using radioactive tracers |
| ISO 3126-2005 |
Plastics piping systems -Plastics components - Determination of dimensions |
| ISO 3183-1-1996 |
Petroleum and natural gas industries - Steel pipe for pipelines - Technical delivery conditions - Part 1: Pipes of requirement class A |
| ISO 3183-2-1996 |
Petroleum and natural gas industries - Steel pipe for pipelines - Technical delivery conditions - Part 2: Pipes of requirements class B |
| ISO 3183-3 Technical Corrigendum 1-2000 |
Petroleum and natural gas industries - Steel pipe for pipelines - Technical delivery conditions - Part 3: Pipes of requirement class C - Technical Corrigendum 1 |
| ISO 3183-3-1999 |
Petroleum and natural gas industries - Steel pipe for pipelines - Technical delivery conditions - Part 3: Pipes of requirement class C |
| ISO 3586-1976 |
Glass plant, pipeline and fittings; general rules for testing, handling and use |
| ISO 3587-1976 |
Glass plant, pipeline and fittings; Pipeline and fittings of nominal bore 15 to 150 mm; Compatibility and interchangeability |
| ISO 3633-2002 |
Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) |
| ISO 4006-1991 |
Measurement of fluid flow in closed conduits; vocabulary and symbols |
| ISO 4059-1978 |
Polyethylene (PE) pipes; Pressure drop in mechanical pipe-jointing systems; Method of test and requirements |
| ISO 4144-2003 |
Pipework - Stainless steel fittings threaded in accordance with ISO 7-1 |
| ISO 4179-2005 |
Ductile iron pipes and fittings for pressure and non-pressure pipelines - Cement mortar lining |
| ISO 4185 Technical Corrigendum 1-1993 |
Measurement of liquid flow in closed conduits; weighing method; technical corrigendum 1 |
| ISO 4185-1980 |
Measurement of liquid flow in closed conduits; Weighing method |
| ISO 4435-2003 |
Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) |
| ISO 4633-2002 |
Rubber seals - Joint rings for water supply, drainage and sewerage pipelines - Specification for materials |
| ISO 4704-1977 |
Glass plant, pipeline and fittings; Glass plant components |
| ISO 5136-2003 |
Acoustics - Determination of sound power radiated into a duct by fans and other air-moving devices - In-duct method |
| ISO 5167-1 Technical Corrigendum 1-1997 |
Measurement of fluid flow by means of pressure differential devices - Part 1: Orifice plates, nozzles and Venturi tubes inserted in circular cross-section conduits running full - Technical Corrigendum 1 |
| ISO 5167-1-2003 |
Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements |
| ISO 5167-2-2003 |
Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 2: Orifice plates |
| ISO 5167-3-2003 |
Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles |
| ISO 5167-4-2003 |
Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 4: Venturi tubes |
| ISO 5176-1-1991 |
Measurement of fluid flow by means of pressure differential devices; part 1: orifice plates, nozzles and Venturi tubes inserted in circular cross-section conduits running full |
| ISO 5667-5-2006 |
Water quality - Sampling - Part 5: Guidance on sampling of drinking water from treatment works and piped distribution systems |
| ISO 5752-1982 |
Metal valves for use in flanged pipe systems; Face-to-face and centre-to-face dimensions |
| ISO 580-2005 |
Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating |
| ISO 6412-1-1989 |
Technical drawings; simplified representation of pipelines; part 1: general rules and orthogonal representation |
| ISO 6412-2-1989 |
Technical drawings; simplified representation of pipelines; part 2: isometric projection |
| ISO 6412-3-1993 |
Technical drawings; simplified representation of pipelines; part 3: terminal features of ventilation and drainage systems |
| ISO 6448-1985 |
Rubber seals; Joint rings used for petroleum product supply pipes and fittings; Specification for material |
| ISO 6773-1994 |
Aerospace - Fluid systems - Thermal shock testing of piping and fittings |
| ISO 6817-1992 |
Measurement of conductive liquid flow in closed conduits; method using electromagnetic flowmeters |
| ISO 6944-1985 |
Fire resistance tests; Ventilation ducts |
| ISO 7235-2003 |
Acoustics - Laboratory measurement procedures for ducted silencers and air-terminal units - Insertion loss, flow noise and total pressure loss |
| ISO 7268 AMD 1-1984 |
Amendment 1-1984 |
| ISO 7268-1983 |
Pipe components; Definition of nominal pressure |
| ISO 7278-2-1988 |
Liquid hydrocarbons; dynamic measurement; proving systems for volumetric meters; part 2: pipe provers |
| ISO 7278-4-1999 |
Liquid hydrocarbons - Dynamic measurement - Proving systems for volumetric meters - Part 4: Guide for operators of pipe provers |
| ISO 7369-2004 |
Pipework - Metal hoses and hose assemblies - Vocabulary |
| ISO 7396-1-2002 |
Medical gas pipeline systems - Part 1: Pipelines for compressed medical gases and vacuum |
| ISO 7396-2-2000 |
Medical gas pipeline systems - Part 2: Anaesthetic gas scavenging disposal systems |
| ISO 7432-2002 |
Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals |
| ISO 7509-2000 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of time to failure under sustained internal pressure |
| ISO 7510-1997 |
Plastics piping systems - Glass-reinforced plastics (GRP) components - Determination of the amounts of constituents using the gravimetric method |
| ISO 7511-1999 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the leaktightness of the wall under short-term internal pressure |
| ISO 7671-2003 |
Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Polypropylene (PP) |
| ISO 7675-2003 |
Plastic piping systems for soil and waste discharge (low and high temperature) inside buildings - Chlorinated poly(vinyl chloride) (PVC-C) |
| ISO 7682-2003 |
Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Acrylonitrile-butadiene-styrene (ABS) |
| ISO 7684-1997 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the creep factor under dry conditions |
| ISO 7685-1998 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial specific ring stiffness |
| ISO 8277-1988 |
Shipbuilding; pipework; information transfer |
| ISO 8316-1987 |
Measurement of liquid flow in closed conduits; Method by collection of the liquid in a volumetric tank |
| ISO 8513-2000 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of longitudinal tensile properties |
| ISO 8521-1998 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the apparent initial circumferential tensile strength |
| ISO 8770-2003 |
Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Polyethylene (PE) |
| ISO 8795-2001 |
Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Determination of migration values of plastics pipes and fittings and their joints |
| ISO 9080-2003 |
Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| ISO 9104-1991 |
Measurement of fluid flow on closed conduits; methods of evaluating the performance of electromagnetic flow-meters for liquids |
| ISO 9170-1-1999 |
Terminal units for medical gas pipeline systems - Part 1: Terminal units for use with compressed medical gases and vacuum |
| ISO 9170-2-1999 |
Terminal units for medical gas pipeline systems - Part 2: Terminal units for anaesthetic gas scavenging systems |
| ISO 9311-1-2005 |
Adhesives for thermoplastic piping systems - Part 1: Determination of film properties |
| ISO 9311-2-2002 |
Adhesives for thermoplastic piping systems - Part 2: Determination of shear strength |
| ISO 9311-3-2005 |
Adhesives for thermoplastic piping systems - Part 3: Test method for the determination of resistance to internal pressure |
| ISO 9349-2004 |
Preinsulated ductile iron pipeline systems |
| ISO 9368-1-1990 |
Measurement of liquid flow in closed conduits by the weighing method; procedures for checking installations; part 1: static weighing systems |
| ISO 9398-3-2003 |
Specifications for industrial laundry machines - Definitions and testing of capacity and consumption characteristics - Part 3: Washing tunnels |
| ISO 9631-2003 |
Rubber seals - Joint rings for pipelines for hot-water supply up to 110 degrees C - Specification for the material |
| ISO 9803-1993 |
Vacuum technology; pipeline fittings; mounting dimensions |
| ISO 9853-1991 |
Injection-moulded unplasticized poly(vinyl chloride) (PVC-U) fittings for pressure pipe systems; crushing test |
| ISO 9951 Technical Corrigendum 1-1994 |
Measurement of gas flow in closed conduits - Turbine meters; Technical Corrigendum 1 |
| ISO 9951-1993 |
Measurement of glas flow in closed conduits; turbine meters |
| ISO/TR 11295-1992 |
Techniques for rehabilitation of pipeline systems by the use of plastics pipes and fittings |
| ISO/TR 12764-1997 |
Measurement of fluid flow in closed conduits - Flowrate measurement by means of vortex shedding flowmeters inserted in circular cross-section conduits running full |
| ISO/TR 3313-1998 |
Measurement of fluid flow in closed conduits - Guidelines on the effects of flow pulsations on flow-measurement instruments |
| ISO/TR 9824-1-1990 |
Measurement of free surface flow in closed conduits; part 1: methods |
| ISO/TR 9824-2-1990 |
Measurement of free surface flow in closed conduits; part 2: equipment |
| ISO/TS 15874-7-2003 |
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 7: Guidance for the assessment of conformity |
| ISO/TS 15875-7-2003 |
Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 7: Guidance for the assessment of conformity |
| ISO/TS 15876-7-2003 |
Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 7: Guidance for the assessment of conformity |
| ISO/TS 15877-7-2003 |
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity |
| ISO/TS 7024-2005 |
Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Thermoplastics - Recommended practice for installation |
Mail consultation
Please feel free to give your inquiry in the form below.We will reply you in 24 hours.
News List
feature product
Contact Us