NF pipe standards
NF pipe standards
| Standards | Application |
|---|---|
| NF A05-671-2001 |
(Cathodic protection for submarine pipelines.) |
| NF A48-810-1995 |
(Ductile iron pipes, fittings, accessories and their joints for gas pipelines. Requirements and test methods.) |
| NF A48-810/A1-1999 |
(Ductile iron pipes, fittings, accessories and their joints for gas pipelines. Requirements and test methods.) |
| NF A48-830-1983 |
(Foundry products. Spheroidal graphite cast iron sittings for PVC drinking water pipes under pressure.) |
| NF A48-840-1984 |
(FOUNDRY PRODUCTS. SPHEROIDAL GRAPHITE CAST IRON PIPES. FLANGES SERIES. FLANGES DEFINITION. DIMENSIONS. SPECIFICATIONS.) |
| NF A48-850-1984 |
(FOUNDRY PRODUCTS. DUCTILE CAST IRON PIPING ELEMENTS FOR PRE-INSULATED PIPELINE. PRE-INSULATED PIPES,SOCKET SERIE. TECHNICAL SPECIFICATION.) |
| NF A48-851-1985 |
(FOUNDRY PRODUCTS. DUCTILE IRON PIPES FOR PRESSURE PIPELINES. POLYURETHAN EXTERNAL COATING.) |
| NF A48-860-1981 |
(Foundry products. Ductile cast iron piping elements. Socket serie. GS express joint. Assembly dimensions and joint accessories.) |
| NF A48-870-1981 |
(Foundry products. Ductile cast iron piping elements. Socket series. GS standard joint. Assembly dimensions and joint accessories.) |
| NF A48-902-1985 |
(Foundry products. Ductile iron pipes for pressure pipelines. Contrifugal cement mortar internal lining. Composition controls of freshly applied mortar.) |
| NF A49-117-1985 |
(Steel tubes. Seamless plain end tubes for pipes-lines and other uses. Ferritic and austenitic stainless steels. Dimensions. Technical delivery conditions.) |
| NF A49-147-1980 |
(STEEL TUBES. PLAIN END LONGITUDINALLY WELDED TUBES FOR PIPE LINES AND GENERAL USE. AUSTENITIC STAINLESS STEELS. DIMENSIONS. TECHNICAL DELIVERY CONDITIONS.) |
| NF A49-148-1980 |
(STEEL TUBES. PLAIN END LONGITUDINALLY WELDED TUBES FOR PIPE LINES AND GENERAL USE. FERRITIC STAINLESS STEELS. DIMENSIONS. TECHNICAL DELIVERY CONDITIONS.) |
| NF A49-170-1-1999 |
(Butt-welding pipe fittings - Part 1 : Wrought carbon steel for general use and without specific inspection requirements.) |
| NF A49-750-1994 |
(Preinsulated bonded pipe systems for underground hot water networks. Pipe assembly of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene.) |
| NF A49-751-1994 |
(Preinsulated bonded pipe systems for underground hot water networks. Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene.) |
| NF A51-126-1-2001 |
(Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 1 : tubes for piping systems.) |
| NF A72-120-1973 |
(LARGE DIAMETER PIPES AND VALVES FOR GASEOUS FLUIDS. FLANGE CONNECTIONS PN 6.) |
| NF A91-701-1999 |
(Surface treatment. Identification of workshop tanks, piping and equipment. Safety marking.) |
| NF C30-400-2003 |
(Electromagnetic locators for buried pipes and cables - Performance and safety.) |
| NF C46-304-1991 |
(Transmitters for use in industrail-process control systems. Guidance for inspection and routing testing.) |
| NF C68-111/A11-2002 |
(Conduit systems for cable management - Part 2-1 : particular requirements for rigid conduit systems.) |
| NF C68-112/A11-2002 |
(Conduit systems for cable management - Part 2-2 : particular requirements for pliable conduit systems.) |
| NF C68-113/A11-2002 |
(Conduit systems for cable management - Part 2-3 : particular requirements for flexible conduit systems.) |
| NF C68-114/A1-2001 |
(Conduit systems for cable management - Part 2-4 : particular requirements for conduit systems buried underground.) |
| NF C68-120-1997 |
(CABLE TRUNKING SYSTEMS AND CABLE DUCTING SYSTEMS FOR ELECTRICAL INSTALLATIONS. PART 1 : GENERAL REQUIREMENTS. (EUROPEAN STANDARD EN 50 085-1).) |
| NF C68-120/A1-2002 |
(Cable trunking systems and cable ducting systems for electrical installations - Part 1 : general requirements.) |
| NF C93-859-1-2001 |
(Familly Specification : optical telecommunication cables to be used in ducts or direct buried application.) |
| NF C93-859-5-2002 |
(Single-mode optical fibre cable (duct/direct buried installation).) |
| NF D36-103-2001 |
(Household economy - (Reinforced) flexible rubber tubing for the external connection of domestic appliances using gaseous fuels by networks.) |
| NF D36-107-1994 |
(Household economy. Flexible piping based on polyamide 11 or 12 for the external connection of domestic appliances using gaseous fuels distributed by networks.) |
| NF D36-121-1994 |
(Household economy. Corrugated metallic flexible piping for the external connection of domestic appliances using gaseous fuels distributed by networks.) |
| NF D36-210-2001 |
(Means for resealing threaded joints of gas pipework in buildings.) |
| NF E03-004-1981 |
(Pipe threads where pressure tight joints are made on the threads (tapered external thread and parallel internal thread).) |
| NF E03-005-1981 |
(Pipe threads where pressure tight joints are not made on the threads (parallel internal and external threads).) |
| NF E03-161-1982 |
(Checking of parallel pipe threads with limit gauges. Introduction.) |
| NF E03-162-1982 |
(Checking of parallel pipe threads with limit gauges. Threaded gauges for screws.) |
| NF E03-163-1982 |
(Checking of parallel pipe threads with limit gauges. Threaded gauges for nuts.) |
| NF E03-165-1984 |
(Checking of pipe threads where pressure tight joints are made on the threards with limit gauges (according to NF E 03-004).) |
| NF E04-118-1-1995 |
(Technical drawings. Simplified representation of pipelines. Part 1 : general rules and orthogonal representation.) |
| NF E04-118-2-1995 |
(Technical drawings. Simplified representation of pipelines. Part 2 : isometric projection.) |
| NF E04-118-3-1996 |
(TECHNICAL DRAWINGS. SIMPLIFIED REPRESENTATION OF PIPELINES. PART 3 : TERMINAL FEATURES OF VENTILATION AND DRAINAGE SYSTEMS. (EUROPEAN STANDARD EN ISO 6412-3).) |
| NF E04-202-1-1996 |
(Pipelines, pipe components and apparatus for industrial processes. Symbolic representation. Part 1 : basic requirements.) |
| NF E04-202-2-1996 |
(Pipelines, pipe components and apparatus for industrial processes. Symbolic representation. Part 2 : pipelines and junctions.) |
| NF E04-202-3-1996 |
(Pipelines, pipe components and apparatus for industrial processes. Symbolic representation. Part 3 : mechanical drive and fluid displacement components.) |
| NF E04-202-4-1996 |
(Pipelines, pipe components and apparatus for industrial processes. Symbolic representation. Part 4 : heat equipment.) |
| NF E04-202-8-2003 |
(Pipelines, pipe components and apparatus for industrial processes - Symbolic representation - Part 8 : comminution, shaping and other process.) |
| NF E04-202-9-2003 |
(Pipelines, pipe components and apparatus for industrial processes - Symbolic representation - Part 9 : storage, handling.) |
| NF E09-081-6-1999 |
(Safety of machinery. Evaluation of the emission of airborne hazardous substances. Part 6 : separation efficiency by mass, unducted outlet.) |
| NF E09-081-7-1999 |
(Safety of machinery. Evaluation of the emission of airborne hazardous substances. Part 7 : separation efficiency by mass, ducted outlet.) |
| NF E17-002-1994 |
(Measurement of water flow in closed conduits. Meters for cold potable water. Part 1 : specifications.) |
| NF E17-006-1986 |
(Measurement of water flow in closed conduits. Meters for cold potable water. Combination meters. Part 1 : specifications.) |
| NF E17-007-1988 |
(Measurement of water flow in closed conduits. Meters for cold potable water. Combination meters. Part 2 : installation requirements.) |
| NF E17-008-1995 |
(Measurement of water flow in closed conduits. Meters for cold potable water. Combination meters. Part 3 : test methods.) |
| NF E29-008-1972 |
(TEMPERATURE AND PRESSURE LIMITATIONS FOR PIPING SYSTEMS MANUFACTURED FROM 23% NICKEL 4% MANGANESE SPHEROIDAL GRAPHITE AUSTENITIC CAST IRON`.) |
| NF E29-009-1972 |
(TEMPERATURE AND PRESSURE LIMITATIONS FOR PIPING SYSTEMS MANUFACTURED FROM 20% NICKEL 2% CHROMIUM SPHEROIDAL GRAPHITE AUSTENITIC CAST IRON`.) |
| NF E29-011-1983 |
(PIPEWORK. TERMS AND DEFINITION.) |
| NF E29-018-1986 |
(Industrial pipework. Bracing rings for flanges with female (groove or spigot), or male(tongue or spigot) faces. ISO PN 2,5 to ISO PN 50.) |
| NF E29-032-1985 |
(Industrial pipework. Steel components. Butt welding ends. Preparation.) |
| NF E29-033-1994 |
(Preinsulated bonded pipe systems for underground hot water networks. Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene.) |
| NF E29-041-1994 |
(INDUSTRIAL PIPEWORK. REDUCED SHANK BOLTS. SPECIFICATIONS.) |
| NF E29-043-1990 |
(Industrial pipework. Non alloy and alloy. Steel bolting for flanged assemblies of pipeworks, boilers and pressure vessels. Specifications.) |
| NF E29-134-1978 |
(SAFETY RELEASE DEVICES WITH BUILT-IN STOP TAP AND TWO G 1/2 MALE UNION CONNECTIONS FOR DOMESTIC APPLIANCES USING MAINS GAS FUELS.) |
| NF E29-204-1992 |
(Industrial pipeworks. Forged steel flanges and collars. Materials. Mechanical properties. Fabrication. Tests.) |
| NF E29-207-1986 |
(INDUSTRIAL PIPEWORK. COPPER ALLOYS FLANGES AND COLLARS AND COMPOSITE FLANGES. TERMINOLOGY. DIMENSIONS. SPECIFICATIONS.) |
| NF E29-210-1985 |
(INDUSTRIAL PIPEWORK. ORIFICE FLANGES FOR DIFFERENTIAL PRESSURE DEVICES.) |
| NF E29-220-1986 |
(INDUSTRIAL PIPEWORK. FLANGED ADAPTERS AND DISASSEMBLY SEAL FOR PIPEWORK. SPECIFICATIONS.) |
| NF E29-251-1972 |
(STAMPED STAINLESS-STEEL FILLETS FOR WELDING (THIN SERIES) PN 10) |
| NF E29-260-1987 |
(Industrial pipes. Pipe components with PTFE - FEP - PFA fluorocarbon resin.) |
| NF E29-302-2-1996 |
(Industrial valves. Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems. Part 2 : class-designated valves.) |
| NF E29-480-1994 |
(Preinsulated bonded pipe systems for underground hot water networks. Steelvalve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene.) |
| NF E29-531-1981 |
(Pipework. Threaded fittings with gasket on shoulder.) |
| NF E29-539-1981 |
(Pipework. Screwed connecting part with a spheroconical function for heating plants.) |
| NF E29-573-1988 |
(Industrial pipework. “Express“ connections. Maximum permissible working pressure 1 MPa (10 bar).) |
| NF E29-577-1978 |
(PIPEWORKS. SCREWED CONNECTIONS FOR PNEUMATIC TOOLS AND MACHINES.) |
| NF E29-591-1-1998 |
(Copper and copper alloys. Plumbing fittings. Part 1 : fittings with ends for capillary soldering or capillary brazing to copper tubes.) |
| NF E29-591-2-1998 |
(COPPER AND COPPER ALLOYS. PLUMBING FITTINGS. PART 2 : FITTINGS WITH COMPRESSION ENDS FOR USE WITH COPPER TUBES. (EUROPEAN STANDARD EN 1254-2).) |
| NF E29-591-3-1998 |
(COPPER AND COPPER ALLOYS. PLUMBING FITTINGS. PART 3 : FITTINGS WITH COMPRESSION ENDS FOR USE WITH PLASTICS PIPES. (EUROPEAN STANDARD EN 1254-3).) |
| NF E29-591-4-1998 |
(COPPER AND COPPER ALLOYS. PLUMBING FITTINGS. PART 4 : FITTINGS COMBINING OTHER END CONNECTIONS WITH CAPILLARY OR COMPRESSION ENDS. (EUROPEAN STANDARD EN 1254-4).) |
| NF E29-591-5-1998 |
(COPPER AND COPPER ALLOYS. PLUMBING FITTINGS. PART 5 : FITTINGS WITH SHORT ENDS FOR CAPILLARY BRAZING TO COPPER TUBES. (EUROPEAN STANDARD EN 1254-5).) |
| NF E29-600-1987 |
(Industrial pipework. Steel fittings and plugs. Socket welding fittings.) |
| NF E29-726-1974 |
(VACUUM TECHNOLOGY. STEEL TUBES FOR VACUUM PIPES. DIMENSIONS) |
| NF E29-802-2000 |
(Malleable cast iron fittings with compression ends for polyethylene (PE) piping systems.) |
| NF E29-820-1983 |
(Pipeworks. Flexible metal hoses. Terminology.) |
| NF E29-821-1983 |
(Pipeworks. Flexible interlocked metal hoses. Specifications .) |
| NF E29-833-1979 |
(PIPEWORKS. FLEXIBLE METAL HOSES DOUBLE INTERLOCK,ASBESTOS PACKING,PRESSURE-TIGHT,CIRCULAR SECTION,IN AUSTENITIC STAINLESS STEEL.) |
| NF E29-834-2003 |
(Pipework - Corrugated metal hoses and hose assemblies.) |
| NF E29-836-1997 |
(Pipework. Corrugated flexible metallic hose assemblies for the protection of electrical cables in explosive atmosphere.) |
| NF E29-850-1974 |
(PIPE SUPPORTS. GENERAL.) |
| NF E29-951-1975 |
(LENSES AND LENS_SHAPED SEALS FOR FLAT OR RAISED FLANGES GN 64 TO GN160.) |
| NF E29-960-1985 |
(Industrial pipework. Suction pipe for atmospheric polluants. Terms and definitions.) |
| NF E29-961-1985 |
(Industrial pipework. Suction pipe for atmospheric polluants. Basic metal components . Specifications.) |
| NF E29-962-1987 |
(Industrial pipework. Suction pipe for atmospheric pollutants. Additionnal metal components . Specifications.) |
| NF E29-963-1988 |
(Industrial pipework. Suction devices. Design requirements. Model for a technical sheet.) |
| NF E31-330-2-2000 |
(Installations for oil supply systems for oil burners - Part 2 : safety requirements and tests : parts, valves, pipes, filters, oil de-aerators, meters.) |
| NF E35-303-1960 |
(REFRIGERATING SYSTEMS. TUNNEL-TYPE FREEZERS FOR FRUIT,EGGS,LIQUIDS,MEAT,GIBLETS,ETC.) |
| NF E35-413-2001 |
(Refrigerating systems and heat pumps - Pressure relief devices and their associated piping - Methods for calculation.) |
| NF E35-415-1998 |
(REFRIGERATING SYSTEMS AND HEAT PUMPS. SYSTEM FLOW DIAGRAMS AND PIPING AND INSTRUMENT DIAGRAMS. LAYOUT AND SYMBOLS. (EUROPEAN STANDARD EN 1861).) |
| NF E39-011-2003 |
(District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene) |
| NF E39-012-2003 |
(District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Fitting assemblies for steel service pipes, polyurethane thermal insulation and outer casing of polye) |
| NF E39-013-2003 |
(District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of pol) |
| NF E39-014-2003 |
(District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of poluethyl) |
| NF E48-392-2-2001 |
(Hydraulic fluid power - Determination of the fluid-borne noise characteristics of components and systems - Part 2 : measurement of the speed of sound in a fluid in a pipe.) |
| NF E49-300-2000 |
(Pneumatic fluid power - Method of characterization of air debit coefficients by drains reservoir.) |
| NF E51-708-2002 |
(Ventilation for buildings - Ductwork - Dimensions and mechanical requirements for flexible ducts.) |
| NF E51-717-2003 |
(Ventilation for buildings - Ductwork - Strength and leakage of circular sheet metal ducts.) |
| NF E51-720-1998 |
(Ventilation for buildings. Ductwork. Dimensions of circular flanges for general ventilation.) |
| NF E51-721-2002 |
(Ventilation for buildings - Ductwork hangers and supports - Requirements for strength.) |
| NF E51-733-2003 |
(Ventilation for buildings - Non-metallic ducts - Ductwork made from insulation ductboards.) |
| NF E58-125-1998 |
(EARTH-MOVING MACHINERY. SAFETY. PART 9 : REQUIREMENTS FOR PIPELAYERS. (EUROPEAN STANDARD EN 474-9).) |
| NF E66-153-1990 |
(Hand-and machine-operated circular screwing dies for parallel pipe threads. G series.) |
| NF E66-154-1990 |
(Hand- and machine-operated circular screwing dies for taper pipe threads. R series.) |
| NF E86-700-1-2002 |
(Metallic industrial piping - Part 1 : general.) |
| NF E86-700-2-2002 |
(Metallic industrial piping - Part 2 : materials.) |
| NF E86-700-3-2002 |
(Metallic industrial piping - Part 3 : design and calculation.) |
| NF E86-700-4-2002 |
(Metallic industrial piping - Part 4 : fabrication and installation.) |
| NF E86-700-5-2002 |
(Metallic industrial piping - Part 5 : inspection and testing.) |
| NF F24-003-1968 |
(RAILWAY TRANSPORT EQUIPMENT. WEIGHT-SAVING EQUIPMENT. PIPEWORK. REMOVABLE PIPE AND NOSE COUPLINGS WITH TORIC BEARING SURFACE SLEEVES AND TAIL ENDS.) |
| NF F24-004-1968 |
(RAILWAY TRANSPORT EQUIPMENT. WEIGHT-SAVING EQUIPMENT. PIPEWORK. 3-PIECE REMOVABLE PIPE AND NOSE COUPLINGS WITH TORIC BEARING SURFACE SLEEVES AND TAIL ENDS.) |
| NF F24-005-1968 |
(RAILWAY TRANSPORT EQUIPMENT. WEIGHT-SAVING EQUIPMENT. PIPEWORK. SWIVEL CONNECTORS.) |
| NF J24-020-1957 |
(SHIPBUILDING. FLEXIBLE PIPING. METHODS OF CONNECTING TO SHIPBOARD PIPELINES. GENERAL TABLE.) |
| NF J40-003-1-2002 |
(Ships and marine technology - Identification colour for the content of piping systems - Part 1 : main colours and media.) |
| NF J41-012-1975 |
(SHIPBUILDING. SEA WATER PIPING SYSTEMS. MEASURES FOR CORROSION REDUCTION.) |
| NF J82-000-1967 |
(INLAND NAVIGATION. PIPING. STANDARDS LIST.) |
| NF J82-214-1967 |
(INLAND NAVIGATION. PIPING. SEALING RINGS. CLASSIFICATION AND USE.) |
| NF L40-100-1966 |
(INSTALLATION OF FLUIDS ABOARD AIRCRAFT. BASIC DIMENSIONS OF HOSE CONNECTIONS.) |
| NF L40-201-1988 |
(AEROSPACE. PIPELINES. IDENTIFICATION.) |
| NF L41-210-1983 |
(Fluid systems. Impulse testing of hose, tubing and fittings.) |
| NF L43-711-1976 |
(V BAND COUPLINGS FOR DUCTING AND PIPING. PROFILE DIMENSIONS.) |
| NF M50-009-2000 |
(Gas supply systems - Pipelines for maximum operating pressure over 16 bar - Functional requirements.) |
| NF M51-007-1998 |
(INSTALLATIONS AND EQUIPMENT FOR LNG. SUITABILITY TESTING OF GASKETS DESIGNED FOR FLANGED JOINTS USED ON LNG PIPING. (EUROPEAN STANDARD EN 12308).) |
| NF M82-011-1987 |
(Mining equipment. Flexible venting ducts. Ventubes of the blowing type. Specifications.) |
| NF M82-013-1987 |
(MINING EQUIPMENT. FLEXIBLE VENTING DUCTS. VENTUBES OF THE SUCTION TYPE. SPECIFICATIONS.) |
| NF M87-217-2003 |
(Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms.) |
| NF M87-222-2002 |
(Petroleum and natural gas industries - Pipeline transportation systems - Welding of pipelines.) |
| NF M87-240-2002 |
(Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock - Technical delivery conditions.) |
| NF P16-101-1999 |
(General requirements for components used in hydraulically pressurized discharge pipes, drains and sewers.) |
| NF P16-103-1999 |
(General requirements for components used in pneumatically pressurized discharge pipes, drains and sewers.) |
| NF P16-120-1998 |
(Structural design of buried pipelines under various conditions of loading. Part 1 : general requirements.) |
| NF P16-125-1997 |
(Construction and testing of drains and sewers.) |
| NF P16-126-2000 |
(Trenchless construction and testing of drains and sewers.) |
| NF P16-150-7-1998 |
(DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS. PART 7 : MAINTENANCE AND OPERATIONS. (EUROPEAN STANDARD EN 752-7).) |
| NF P16-250-2-2000 |
(Gravity drainage systems inside buildings - Part 2 : sanitary pipework, layout and calculation.) |
| NF P16-250-3-2000 |
(Gravity drainage systems inside buildings - Part 3 : roof drainage, layout and calculation.) |
| NF P16-304-1997 |
(Fibre-cement pipes for sewers and drains. Part 1 : pipes, joints and fittings for gravity systems.) |
| NF P16-321-1/A3-1999 |
(Vitrified clay pipes and fittings and pipe joints for drains and sewers - Part 1 : requirements.) |
| NF P16-321-3-1992 |
(Vitrified clay pipes and fittings and pipe joints for drains and sewers. Part 3 : test methods.) |
| NF P16-321-5-1994 |
(Vitrified clay pipes and fittings and pipe joints for drains and sewers. Part 5 : requirements for perforated vitrified clay pipes and fittings.) |
| NF P16-321-6-1996 |
(Vitrified clay pipes and fittings and pipe joints for drains and sewers. Part 6 : requirements for vitrified clay manholes.) |
| NF P16-321-7-1996 |
(Vitrified clays pipes and fittings and pipe joints for drains and sewers. Part 7 : requirements for vitrified clay pipes and joints for pipe jacking.) |
| NF P16-325-1-1999 |
(Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems. Part 1 : requirements, testing, quality control.) |
| NF P16-325-2-1999 |
(Pipes and fittings of longitudinally welded, hot-dip galvanized steel pipes with spigot and socket for waste water systems. Part 2 : dimensions.) |
| NF P16-342-1990 |
(DRAINAGE,SEWERAGE. PRECAST CONCRETE ELEMENTS OF MANHOLES FOR SEWAERAGE NETWORKS. DEFINITIONS SPECIFICATIONS,TESTING METHODS,MARKING,BASIS FOR ACCEPTANCE.) |
| NF P16-345-1-2003 |
(Concrete pipes and fittings, unreinforced, steel fibre and reinforced.) |
| NF P16-345-2-2003 |
(Concrete pipes and fittings, unreinforced, steel fibre and reinforced - Part 2 : national specification.) |
| NF P16-351-1998 |
(Plastics. Plastics piping system for civil engineering subsoil drainage. Specification.) |
| NF P16-352-1-1998 |
(Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U). Part 1 : specifications for pipes, fittings and the system.) |
| NF P16-357-1-1997 |
(Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene (PP). Part 1 : specifications for pipes, fittings and the system.) |
| NF P16-357-1/A1-2002 |
(Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1 : specifications for pipes, fittings and the system.) |
| NF P16-358-1-2001 |
(Plastics piping systems for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1 : specifications for piping components and the system.) |
| NF P16-360-2002 |
(Plastics piping systems - Piping systems for underground drainage and sewerage - Test method for resistance to combined temperature cycling and external loading.) |
| NF P16-361-3-1997 |
(Plastics piping systems for non-pressure drainage and sewerage. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Part 3 : fittings.) |
| NF P16-361-5-1997 |
(Plastics piping systems for non-pressure drainage and sewerage. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Part 5 : fitness for purpose of the joints.) |
| NF P16-361-6-1997 |
(Plastics piping systems for non-pressure drainage and sewerage. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Part 6 : practices for installation.) |
| NF P16-364-1-2003 |
(Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 1 : general.) |
| NF P16-364-3-2003 |
(Plastics piping systems for renovation of underground non-pressure drainage and sewerage network - Part 3 : lining with close-fit pipes.) |
| NF P16-364-4-2003 |
(Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4 : lining with cured-in-place pipes.) |
| NF P36-411-1-2000 |
(Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1 : specifications for pipes, fittings and the system.) |
| NF P40-201/A1-1999 |
(DTU 60.1 - Building works - Sanitary plumbing in residencial buildings - Technical specifications.) |
| NF P40-201/A2-2000 |
(DTU 60.1 - Building works - Sanitary plumbing in residential buildings - Technical specifications.) |
| NF P41-030-1999 |
(Influence of organic materials on water intended for human consumption - Determination of odour and flavour assessment of water in piping systems - Part 1 : test method.) |
| NF P41-031-1-2002 |
(Influence of materials on water intended for human consumption - Organic materials - Determination of colour and turbidity of water in piping systems - Part 1 : test method.) |
| NF P41-211/A1-2000 |
(DTU 60.31 - Building works - Unplasticized polyvinyl chloride piping installation - Cold water under pressure - Technical specifications.) |
| NF P41-212/A1-2000 |
(DTU 60.32 - Building works - Unplasticized polivinyl chloride piping installation - Rainwater downpipes - Technical specifications.) |
| NF P41-213-1993 |
(DTU 60.33 - Building works - Unplasticized polyvinyl chloride piping installations - Waste water drainage - Technical specifications.) |
| NF P41-213/A1-2000 |
(DTU 60.33 - Building works - Unplasticized polyvinyl chloride piping installations - Waste water drainage - Technical specifications.) |
| NF P41-220/A1-1999 |
(DTU 60.2 - Building works - Cast ison pipes for soil water, rain water and waste water drainage - Technical specification.) |
| NF P41-220/A2-2000 |
(DTU 60.2 - Building works - Cast iron for soil water, rain water and waste water drainage - Technical specifications.) |
| NF P41-221/A1-1999 |
(DTU 60.5 - Building works - Copper piping. Supply of hot and cold domestic water, drainage of waste water, rainwater, air conditioning installations - Technical specifications.) |
| NF P41-221/A2-2000 |
(DTU 60.5 - Building works - Coper piping - Supply of hot and cold domestic water, drainage of waste water, rainwater, air conditioning installations - Technical specifications.) |
| NF P41-302-1994 |
(Fibre-cement products. Pressure pipes and joints.) |
| NF P45-200-1998 |
(Gas supply - Gas pipework for buildings - Maximum operating pressure inferior or equal to 5 bar - Functional recommendations.) |
| NF P45-200/A1-2000 |
(Gas supply - Gas pipework for buildings - Maximum operating pressure up to and including 5 bar - Functional recommendations.) |
| NF P45-200/A2-2002 |
(Gas supply - Gas pipework for buildings - Maximum operating pressure up to and including 5 bar - Functional recommendations.) |
| NF P50-749-5-2000 |
(Thermal performance of building products and components - Specific criteria for the assessment of laboratories measuring heat transfer properties - Part 5 : measurements by pipe test methods.) |
| NF P52-305-1/A1-1999 |
(DTU 65.10 - Building works - Piping used for cold and hot pressure water and piping for evacuation waste water and rain water inside buildings - General rules of execution - Part 1 : technical specifications.) |
| NF P52-305-1/A2-2000 |
(DTU 65.10 - Building works - Piping used for cold and hot pressure water and piping for evacuation waste water and rain water inside buildings - General rules of execution - Part 1 : technical specifi) |
| NF P52-305-2-1993 |
(DTU 65-10. BUILDING WORKS. PRIVATE CONTRACTS. PIPING USED FOR COLD AND HOT PRESSURE WATER AND PIPING FOR EVACUATION WASTE WATER AND RAIN WATER INSIDE BUILDINGS. GENERAL RULES OF EXECUTION. PART 2 : SPECIAL CLAUSES.) |
| NF R95-403-1970 |
(PIPE FITTINGS WITH DOUBLE TAPER SLEEVES. COUPLING DIMENSIONS.) |
| NF R95-404-1968 |
(PIPE FITTINGS IN TWO PARTS WITH TAPERED BEARING.) |
| NF R95-405-1970 |
(PIPE FITTINGS WITH DOUBLE TAPER SLEEVES. INSERTS.) |
| NF S31-063-2003 |
(Acoustics - Determination of sound power radiated into a duct by fans and other air-moving devices - In-duct method.) |
| NF S95-154-1998 |
(Medical gas pipeline systems - Part 2 : anaesthetic gas scavenging disposal systems - Basic requirements.) |
| NF S95-154/A1-2000 |
(Medical gas pipeline systems - Part 2 : anaesthetic gas scavenging disposal systems - Basic requirements.) |
| NF S95-155-2000 |
(Medical gaz pipeline systems - Part 3 : pipelines for compressed medical gases and vacuum.) |
| NF S95-162-1998 |
(Medical gas pipeline systems. Part 1 : terminal units for compressed medical gases and vacuum.) |
| NF S95-163-1998 |
(Medical gas pipeline systems. Part 4 : terminal units for anaesthetic gas scavenging systems.) |
| NF S95-169-1999 |
(Flow-metering devices for connection to terminal units of medical gas pipeline systems.) |
| NF T47-301-1972 |
(RUBBER MOLDED AND EXTRUDED SEALING RINGS AND PROFILES FOR PIPE WORK. GENERAL SPECIFICATIONS OF MATERIALS.) |
| NF T47-305-1/A2-2003 |
(Elastomeric seals - Material requirements for pipe joints seals used in water and drainage applications - Part 1 : vulcanized rubber.) |
| NF T47-305-2/A1-2003 |
(Elastomeric seals - Material requirements for pipe joints seals used in water and drainage applications - Part 2 : thermoplastic elastomers.) |
| NF T47-305-3/A1-2003 |
(Elastomeric seals - Material requirements for joint seals used in water and drainage applications - Part 3 : cellular materials of vulcanized rubber.) |
| NF T47-305-4/A1-2003 |
(Elastomeric seals - Material requirements for pipe joint seals in water and drainage applications - Part 4 : cast polyurethane sealing elements.) |
| NF T47-306-2003 |
(Elastomeric seals - Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids.) |
| NF T54-006-2003 |
(Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for the resistance to dichloromethane at a specified temperature (DCMT).) |
| NF T54-007-1994 |
(THERMOPLASTICS PIPING SYSTMES. END-LOAD BEARING MECHANICAL JOINTS BETWEEN PRESSURE PIPES AND FITTINGS. TEST METHOD FOR RESISTANCE TO PULL-OUT UNDER CONSTANT LONGITUDINAL FORCE. (EUROPEAN STANDARD EN 712).) |
| NF T54-008-1994 |
(PLASTICS PIPING SYSTEMS. MECHANICAL JOINTS BETWEEN FITTINGS AND POLYOLEFIN PRESSURE PIPES. TEST METHOD FOR LEAKTIGHTNESS UNDER INTERNAL PRESSURE OF ASSEMBLIES SUBJECTED TO BENDING. (EUROPEAN STANDARD EN 713).) |
| NF T54-009-1994 |
(THERMOPLASTICS PIPING SYSTEMS. NON-END-LOAD-BEARING ELASTOMERIC SEALING RING TYPE JOINTS BETWEEN PRESSURE PIPES AND MOULDED FITTINGS. TEST METHOD FOR LEAKIGHTNESS UNDER INTERNAL HYDROSTATIC PRESSURE WITHOUT END THRUST. (EUROPEAN STANDARD EN 714).) |
| NF T54-010-1994 |
(THERMOPLASTICS PIPING SYSTEMS. END-LOAD BEARING JOINTS BETWEEN SMALL DIAMETER PRESSURE PIPES AND FITTINGS. TEST METHOD FOR LEAKTIGHTNESS UNDER INTERNAL WATER PRESSURE, INCLUDING END THRUST. (EUROPEAN STANDARD EN 715).) |
| NF T54-012-1995 |
(PLASTICS PIPING SYSTEMS. ELASTOMERIC SEALING RING TYPE JOINTS AND MECHANICAL JOINTS FOR THERMOPLASTICS PRESSURE PIPING. TEST METHOD FOR LEAKTIGHTNESS UNDER EXTERNAL HYDROSTATIC PRESSURE. (EUROPEAN STANDARD EN 911).) |
| NF T54-015-1997 |
(Plastics piping systems. Thermoplastics valves. Test methods for resistance to internal pressure and leaktightness.) |
| NF T54-016-1-1999 |
(Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1 : general.) |
| NF T54-016-2-1999 |
(Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2 : pipes.) |
| NF T54-016-3-1999 |
(Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3 : fittings.) |
| NF T54-016-4-1999 |
(Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4 : valves and ancillary equipment.) |
| NF T54-016-5-1999 |
(Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 5 : fitness for purpose of the system.) |
| NF T54-017-1-1999 |
(Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U). Part 1: Specifications for pipes, fittings and the system.) |
| NF T54-019-1995 |
(PLASTICS PIPING AND DUCTING SYSTEMS. PIPES AND FITTINGS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U). SPECIMEN PREPARATION FOR DETERMINATION OF THE VISCOSITY NUMBER AND CALCULATION OF THE K-VALUE. (EUROPEAN STANDARD EN 922).) |
| NF T54-024-1994 |
(PLASTICS PIPING AND DUCTING SYSTEMS. THERMOPLASTICS PIPES AND FITTINGS. DETERMINATION OF VICAT SOFTENING TEMPERATURE (VST). (EUROPEAN STANDARD EN 727).) |
| NF T54-025-1995 |
(Plastics piping systems. Thermoplastics pipes. Determination of resistance to internal pressure at constant temperature.) |
| NF T54-036-1994 |
(Plastics piping and ducting systems. Injection-moulded thermoplastics fitting. Test method for visually assessing effects of heating.) |
| NF T54-037-1981 |
(Plastics. Un-plasticized PVC parts dor piping. Simple assemblies with sealing rings for domestic water drainage piping. End use test. Specification.) |
| NF T54-041-1994 |
(Plastics piping systems. Injection-moulded thermoplastics fittings for elastic sealing ring type joints for pressure piping. Test method for resistance to a short-term internal pressure without end thrust.) |
| NF T54-042-1994 |
(Plastics piping systems. Injection-moulded socket fittings for solvent-cemented joints for pressure piping. Test method for resistance to a short-term internal hydrostatic pressure.) |
| NF T54-045-1994 |
(Plastics piping and ducting systems. Injection-moulded thermoplastics fittings for pressure piping systems. Test method for maximum deformation by crushing.) |
| NF T54-051-1979 |
(Polyethylene pipes. Pressure drop in mechanical pipe-jointing systems. Method of test and requirements.) |
| NF T54-052-2001 |
(Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Determination of migration values of plastics pipes and fittings and their joints.) |
| NF T54-054-1997 |
(Plastics piping systems. Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double socket joints. Test method for leaktightness and strength while subjected to bending and internal pressure.) |
| NF T54-059-1995 |
(Thermoplastics materials for pipes and fittings for pressure applications. Classification and designation. Overall service (design) coefficient.) |
| NF T54-062-1-1999 |
(Plastics piping systems for soils and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 1 : specifications for pipes, fittings and the system.) |
| NF T54-063-1-2003 |
(Plastics piping systems for water supply - Polyethylene (PE) - Part 1 : general.) |
| NF T54-063-2-2003 |
(Plastics piping systems for water supply - Polyethylene (PE) - Part 2 : pipes.) |
| NF T54-063-3-2003 |
(Plastics piping systems for water supply - Polyethylene (PE) - Part 3 : fittings.) |
| NF T54-063-4-2003 |
(Plastics piping systems for water supply - Polyethylene (PE) - Part 4 : valves.) |
| NF T54-063-5-2003 |
(Plastics piping systems for water supply - Polyethylene (PE) - Part 5 : fitness for purpose of the system.) |
| NF T54-065-1-2003 |
(Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1 : general.) |
| NF T54-065-2-2003 |
(Plastics piping systems for the supply of gaseous fuels - Polythylene (PE) - Part 2 : pipes.) |
| NF T54-065-3-2003 |
(Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3 : fittings.) |
| NF T54-065-4-2003 |
(Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4 : valves.) |
| NF T54-065-5-2003 |
(Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5 : fitness for purpose of the system.) |
| NF T54-075-1997 |
(Plastics piping and ducting systems. Polyolefin pipes and fittings. Determination of oxidation induction time.) |
| NF T54-076-1992 |
(Plastics. Polyethylene (pe) plastics piping systems. Resistance to slow cracking of pipes with a nominal external diameter over 125. Test method.) |
| NF T54-077-1992 |
(Plastic. Polyethylene (pe) plastics piping systems. Resistance to slow cracking of pipes with a nominal external diameter up to 125. Test method.) |
| NF T54-078-1992 |
(Plastics. Polyethylene (pe) for plastics piping systems. Determination of the limiting stress intensity factor. Test method.) |
| NF T54-087-1993 |
(PLASTICS PIPING SYSTEMS. CROSSLINKED POLYETHYLENE (PE-X) PIPES. DETERMINATION OF DEGREE OF CROSSLINKING BY SOLVENT EXTRACTION. (EUROPEAN STANDARD EN 579).) |
| NF T54-097-1995 |
(Plastics piping and ducting systems. Thermoplastics pipes. Test method for resistance to external blows by the round-the-clock method.) |
| NF T54-100-1997 |
(Plastics piping systems. Thermoplastics valves. Test method for the integrity of a valve after an external blow.) |
| NF T54-300-1-2003 |
(Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 1 : general.) |
| NF T54-300-2-2003 |
(Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 2 : pipes.) |
| NF T54-300-3-2003 |
(Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 3 : fittings.) |
| NF T54-300-4-2003 |
(Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 4 : valves.) |
| NF T54-300-5-2003 |
(Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 5 : fitness for purpose of the system.) |
| NF T54-900-2003 |
(Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation.) |
| NF T54-901-1995 |
(Plastics piping systems. Thermoplastics piping systems for non-pressure applications. Test method for watertightness.) |
| NF T54-902-1995 |
(Plastics piping systems. Thermoplastics piping systems for soil and waste discharge. Test method for airtightness of joints.) |
| NF T54-903-1996 |
(Plastics piping systems. Thermoplastics piping systems for soil and waste discharge inside buildings. Test method for resistance to elevated temperature cycling.) |
| NF T54-904-1996 |
(PLASTICS PIPING AND DUCTING SYSTEMS. PLASTICS PIPES AND FITTINGS. METHOD FOR EXPOSURE TO DIRECT (NATURAL) WEATHERING. (EUROPEAN STANDARD EN 1056).) |
| NF T54-905-2002 |
(Plastics piping systems - End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping - Test method for long-term leaktightness under internal water pressure.) |
| NF T54-906-1996 |
(Plastics piping systems. Thermoplastics piping systems for buried non-pressure applications. Test methods for leaktightness of elastomeric sealing ring type joints.) |
| NF T54-911-1995 |
(THERMOPLASTICS PIPES. DETERMINATION OF CREEP RATIO. (EUROPEAN STANDARD EN ISO 9967).) |
| NF T54-912-1995 |
(THERMOPLASTICS. PIPES. DETERMINATION OF RING STIFFNESS. (EUROPEAN STANDARD EN ISO 9969).) |
| NF T54-913-1996 |
(PLASTICS PIPING AND DUCTING SYSTEMS. THERMOPLASTICS PIPES. DETERMINATION OF RING FLEXIBILITY. (EUROPEAN STANDARD EN 1446).) |
| NF T54-914-1-2000 |
(Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1 : requirements for pipes, fittings and th) |
| NF T54-915-1-2000 |
(Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1 : specifications for p) |
| NF T54-917-1-2000 |
(Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 1 : specifications for pipes, fittings and the system.) |
| NF T54-918-1-1999 |
(Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN + PVC) - Part 1 : specifications for pipes, fittings and the system.) |
| NF T54-919-1-1999 |
(Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1 : specifications for pipes, fittings and the system.) |
| NF T54-920-1997 |
(Plastics piping systems. Valves for polyethylene (PE) piping systems. Test method for leaktightness under and after bending applied to the operating mechanism.) |
| NF T54-921-1997 |
(Plastics piping systems. Thermoplastics valves. Test method for the integrity of a valve after temperature cycling under bending.) |
| NF T54-922-1997 |
(Plastics piping systems. Polyethylene (PE) tapping tees. Test method for impact resistance of an assembled tapping tee.) |
| NF T54-923-2000 |
(Plastics piping systems - Elastomeric-sealing-ring-type socket joints of unplasticized poly(vinyl chloride) (PVC-U) for use with PVC-U pipes - Test method for leaktightness under negative pressure.) |
| NF T54-924-1999 |
(Plastics piping systems. Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material. Method for assessment of the PVC content based on total chlorine content.) |
| NF T54-925-1999 |
(PLASTICS PIPING AND DUCTING SYSTEMS. THERMOPLASTICS SPIRALLY-FORMED STRUCTURED-WALL PIPES. DETERMINATION OF THE TENSILE STRENGTH OF A SEAM. (EUROPEAN STANDARD EN 1979).) |
| NF T54-926-2000 |
(Thermoplastics piping systems - Joints for buried non-pressure sewage applications - Test method for long-term sealing performance of joints with thermoplastic elastomer (TPE) seals by estimating the) |
| NF T54-927-1999 |
(PLASTICS PIPING SYSTEMS. THERMOPLASTICS FITTINGS. TEST METHOD FOR IMPACT STRENGTH. (EUROPEAN STANDARD EN 12061).) |
| NF T54-928-1997 |
(Plastics piping system. Brackets for rainwater piping systems. Test method for bracket strength.) |
| NF T54-929-1997 |
(Plastics piping systems. Polyethylene piping materials and components. Determination of volatile content.) |
| NF T54-930-1997 |
(Plastics piping systems. Polyethylene (PE) valves. Test method for resistance to bending between supports.) |
| NF T54-931-1997 |
(PLASTICS PIPING SYSTEMS. POLYETHYLENE (PE) PIPES. TEST METHOD FOR THE RESISTANCE TO INTERNAL PRESSURE AFTER APPLICATION OF SQUEEZE-OFF. (EUROPEAN STANDARD EN 12106).) |
| NF T54-932-1997 |
(Plastics piping systems. Injection-moulded thermoplastics fittings, valves and ancillary equipment. Determination of the long-term hydrostatic strength of thermoplastics materials for injection moulding of piping components.) |
| NF T54-934-1997 |
(Plastics piping systems. Fittings, valves and ancillaries. Determination of gaseous flow rate/pressure drop relationships.) |
| NF T54-935-1997 |
(Plastics piping systems. Determination of moisture content in thermoplastics by coulometry.) |
| NF T54-936-1997 |
(Plastics piping systems. Polyethylene (PE) valves. Test method for resistance to thermal cycling.) |
| NF T54-937-2000 |
(Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for leaktightness under internal pressure and with ang) |
| NF T54-939-1998 |
(Plastics piping systems. Thermoplastics fittings. Test method for mechanical strength or flexibility of fabricated fittings.) |
| NF T54-940-1999 |
(PLASTICS PIPING SYSTEMS. THERMOPLASTICS PIPES AND FITTINGS FOR HOT AND COLD WATER. TEST METHOD FOR THE RESISTANCE OF MOUNTED ASSEMBLIES TO TEMPETARURE CYCLING. (EUROPEAN STANDARD EN 12293).) |
| NF T54-941-1999 |
(Plastics piping systems - Systems for hot and cold water - Test method for leaktightness under vacuum.) |
| NF T54-942-1999 |
(Plastics piping systems - Thermoplastics pipes and associated fittings for hot and cold water - Test method for resistance of joints to pressure cycling.) |
| NF T54-946-2003 |
(Plastics piping systems for industrial applications - Polybutene (PB), polyethylene (PE) and polypropylene (PP) - Specifications for components and the system - Metric series.) |
| NF T54-949-2003 |
(Guidance on the classification and design of plastics piping systems used for renovation.) |
| NF T54-956-2003 |
(Plastics piping and ducting systems - Plastics pipes and fittings - Method for exposure to direct (naturel) weathering.) |
| NF T54-965-2003 |
(Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Specifications for the packaging, the storage, the handling and the transportation of the pipes.) |
| NF T57-204-1996 |
(Plastics piping systems. Glass-reinforced thermosetting plastics (grp) pipes. Determination of long-term resistance to internal pressure.) |
| NF T57-210-1994 |
(Plastics piping systems. Glass-reinforced plastics components. Determination of the amounts of constituents using the gravimetric method.) |
| NF T57-211-1994 |
(Plastics piping sytems. Glass-reinforced thermosetting plastics (grp) pipes and fittings. Methods for regression analysis and their use.) |
| NF T57-212-1994 |
(Plastics piping systems. Glass-reinforced thermosetting plastics (grp) pipes. Determination of the creep factor dry conditions.) |
| NF T57-214-1-1998 |
(Plastics piping systems for underground drainage and sewerage under pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Part 1 : general.) |
| NF T57-214-3-1996 |
(Plastics piping systems for underground drainage and sewerage under pressure. Glass-reinforced thermosetting plastics (grp) based on unsaturated polyester resin (up). Part 3 : fittings.) |
| NF T57-214-5-1996 |
(Plastics piping systems for underground drainage and sewerage under pressure. Glass-reinforced thermosetting plastics (grp) based on unsatured polyester resin (up). Part 5: fitness for purpose of the joints.) |
| NF T57-215-1996 |
(Plastics piping systems. Joints for glass-reinforced thermosetting plastics (grp) pipes and fittings. Test methods for leaktightness and resistance to damage of flexible and reduced-articulation joints.) |
| NF T57-216-1996 |
(Plastics piping systems. Glass-reinforced thermosetting plastics (grp) pipes and fittings. Determination of the resistance to chemical attack from the inside of a section in a deflected condition.) |
| NF T57-217-1996 |
(Plastics piping systems. Glass-reinforced thermosetting plastics (grp) pipes. Determination of the creep factor under wet conditions and calculation of the long-term specific ring stiffness.) |
| NF T57-218-1996 |
(Plastics piping systems. Glass-reinforced thermosetting plastics (grp) pipes. Test method to prove the resistance to initial ring deflection.) |
| NF T57-219-1999 |
(Plastics piping systems. Glass-reinforced thermosetting plastics (GRP) pipes. Determination of the long-term ultimate relative ring deflection under wet conditions.) |
| NF T57-220-1996 |
(Plastics piping systems. Glass-reinforced thermosetting plastics (grp) pipes. Determination of initial specific ring stiffness.) |
| NF T57-221-1996 |
(Plastics piping systems. Glass-reinforced thermosetting plastics (grp) pipes and fittings. Test methods to prove the leaktightness of the wall under short-term internal pressure.) |
| NF T57-222-1996 |
(Plastics piping systems. Glass-reinforced thermosetting plastics (grp) pipes. Determination of initial longitudinal tensile properties.) |
| NF T57-223-1996 |
(Plastics piping systems. Glass-reinforced thermosetting plastics (grp) pipes. Determination O the apparent initial circumferential tensile strength.) |
| NF T57-224-1997 |
(Plastics piping systems. Glass-reinforced thermosetting plastics (GRP) components. Test methods to prove the design of rigid locked socket-and-spigot joints with elastomeric seals.) |
| NF T57-225-1997 |
(Plastics piping systems. Glass-reinforced thermosetting plastics (GRP) components. Test methods to prove the design of cemented socket-and-spigot joints.) |
| NF T57-226-1996 |
(Plastics piping systems. Glas-reinforced thermosetting plastics (grp) components. Test methods to prove the design of bolted flange joints.) |
| NF T57-227-1997 |
(Plastics piping systems. Glass-reinforced thermosetting plastics (GRP) pipes. Test method for the effects of cyclic internal pressure.) |
| NF T57-229-1997 |
(Plastics piping systems. Glass-reinforced thermosetting plastics (GRP) pipes. Determination of the relative flexural creep factor following exposure to a chemical environment.) |
| NF T76-320-2003 |
(Adhesives for thermoplastic piping systems - Test method for the determination of thermal stability of adhesives.) |
| NF X08-101-1978 |
(CONVENTIONAL COLOURS FOR PIPING. TABLE OF BASIC PIGMENTS FOR USE IN THE PRODUCTION OF CONVENTIONAL COLOURS FOR PIPING.) |
| NF X08-104-1987 |
(Colours. Iron and stellfactories. Marking of fluids in pipes.) |
| NF X08-105-1986 |
(Colours. Chemical factories. Marking of fluids in pipes.) |
| NF X10-100-1993 |
(Measurement of fluid flow in closed conduits. Vocabulary and symbols.) |
| NF X10-102-1-2003 |
(Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1 : general principles and requirements.) |
| NF X10-102-2-2003 |
(Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 2 : orifice plates.) |
| NF X10-102-3-2003 |
(Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3 : nozzles and Venturi nozzles.) |
| NF X10-102-4-2003 |
(Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 4 : Venturi tubes.) |
| NF X10-112-1977 |
(MEASUREMENT OF FLUID FLOW IN CLOSED CONDUITES.VELOCITY AREA METHOD USING PITOT STATIC TUBES.) |
| NF X10-113-1982 |
(DETERMINATION OF FLOWRATE OF FLUIDS IN CLOSED CONDUITS OF CIRCULAR CROSS-SECTION. METHOD OF VELOCITY MEASUREMENT AT ONE POINT OF THE CROSS-SECTION.) |
| NF X10-121-1993 |
(Measurement of fluid flow in closed conduits. Methods of evaluating the performance of electromagnetic flow-meters for liquids.) |
| NF X10-131-1974 |
(MEASUREMENT OF WATER FLOW IN CLOSED CONDUITS.TRACER METHODS PART I:GENERAL) |
| NF X10-132-1975 |
(MEASUREMENT OF WATER FLOW IN CLOSED CONDUITS. TRACER METHODS PART II : CONSTANT RATE INJECTION METHOD USING NON-RADIOACTIVE TRACERS) |
| NF X10-133-1977 |
(MEASUREMENT OF WATER FLOW RATE IN CLOSED CONDUITS. TRACER METHODS. PART III: CONSTANT RATE INJECTION METHOD USING RADIOACTIVE TRACERS.) |
| NF X10-136-1977 |
(MEASUREMENT OF WATER FLOW IN CLOSED CONDUITS. TRACER METHODS-PAR VI:TRANSIT TIME METHOD USING NON-RADIOACTIVE TRACERS.) |
| NF X10-137-1977 |
(MEASUREMENT OF WATER FLOW IN CLOSED CONDUITS. TRACER METHODS. PART VII:TRANSIT TIME METHOD USING RADIOACTIVE TRACERS.) |
| NF X10-141-1982 |
(Measurement of gas flow in conduits. Tracer methods. Part 1 general.) |
| NF X10-144-1982 |
(MEASUREMENT OF GAS FLOW IN CONDUITS. TRACER METHODS. PART 4 : TRANSIT TIME METHOD USING RADIOACTIVE TRACERS.) |
| NF X10-145-1991 |
(MEASUREMENT OF LIQUID FLOW IN CLOSED CONDUITS BY THE WEIGHING METHOD. PROCEDURES FOR CHECKING INSTALLATIONS. PART 1 : STATIC WEIGHING SYSTEM.) |
| NF X42-119-2001 |
(Biotechnology - Performance criteria for piping and instrumentation - Part 1 : general performance criteria.) |
| NF X42-125-2001 |
(Biotechnology - Performance criteria for piping and instrumentation - Part 2 : couplings.) |
| NF X42-127-2001 |
(Biotechnology - Performance criteria for piping and instrumentation - Part 3 : sampling and inoculation devices.) |
| NF X42-128-2001 |
(Biotechnology - Performance criteria for piping and instrumentation - Part 4 : tubes and pipes.) |
| NF X42-129-2001 |
(Biotechnology - Performance criteria for piping and instrumentation - Part 5 : valves.) |
| NF X42-132-2001 |
(Biotechnology - Performance criteria for piping and instrumentation - Part 6 : equipment probes.) |
| NF X43-285-1997 |
(WORKPLACE ATMOSPHERES. SHORT TERM DETECTOR TUBE MEASUREMENT SYSTEMS. REQUIREMENTS AND TEST METHODS. (EUROPEAN STANDARD EN 1231).) |
| NF X50-001-7-1-2000 |
(Guide for procurement of power station plant, equipement and systems - Part 7 : pipework and valves - Section 1 : high pressure piping systems.) |
| NF X50-001-7-2-2000 |
(Guide for procurement of power station plant, equipment and systems - Part 7 : pipework and valves - Section 2 : boiler and high pressure piping valves.) |
| XP T54-034-1999 |
(Plastics - Unplasticized poly(vinyl chloride) (PVC-U) piping for conveyance under pressure of liquid foodstuffs, thermal water and industrial liquids - Specifications and setting of the derating rules for pressurized liquids.) |