EN pipe standards
EN pipe standards
| Standards | Application |
|---|---|
| CR 12952-17-2002 |
Water boilers and auxiliary installations - Part 17: Guideline for the involvement of an inspection body independent of the manufacturer |
| CR 13932-2000 |
Rotodynamic pumps - Recommendations for fitting of inlet and outlet on piping |
| EN 10208-1-1997 |
Steel pipes for pipelines for combustible fluids - Technical delivery conditions - Part 1: Pipes of requirement class A |
| EN 10208-2-1996+AC-1996 |
Steel pipes for pipelines for combustible fluids - Technical delivery conditions - Part 2: Pipes of requirement class B |
| EN 1053-1995 |
Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test method for watertightness |
| EN 1054-1995 |
Plastics piping systems - Thermoplastics piping systems for soil and waste discharge - Test method for airtightness of joints |
| EN 1055-1996 |
Plastics piping systems - Thermoplastics piping systems for soil and waste discharge inside buildings - Test method for resistance to elevated temperature cycling |
| EN 1093-6-1998 |
Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 6: Separation efficiency by mass, unducted outlet |
| EN 1093-7-1998 |
Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 7: Separation efficiency by mass, ducted outlet |
| EN 1115-1-1997 |
Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 1: General |
| EN 1115-3-1996 |
Plastics piping systems for underground drainage and sewerage under pressure - Glassreinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 3: Fittings |
| EN 1115-5-1996 |
Plastics piping systems for underground drainage and sewerage under pressure - Glassreinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 5: Fitness for purpose of the joints |
| EN 1119-1996 |
Plastics piping systems - Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness and resistance to damage of flexible and reduced-articulation joints |
| EN 1120-1996 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Determination of the resistance to chemical attack from the inside of a section in a deflected condition |
| EN 1123-1-1999 |
Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Part 1: Requirements, testing, quality control |
| EN 1123-1/prA1-2002 |
Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Part 1: Requirements, testing, quality control; Amendment A1 |
| EN 1123-2-1999 |
Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Part 2: Dimensions |
| EN 1124-1-1999 |
Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems - Part 1: Requirements, testing, quality control |
| EN 1124-1/prA1-2002 |
Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems - Part 1: Requirements, testing, quality control; Amendment A1 |
| EN 1124-2-1999 |
Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems - Part 2: System S - Dimensions |
| EN 1124-3-1999 |
Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems - Part 3: System X - Dimensions |
| EN 12056-2-2000 |
Gravity drainage systems inside buildings - Part 2: Sanitary pipework, layout and calculation |
| EN 12061-1999 |
Plastics piping systems - Thermoplastics fittings - Test method for impact resistance |
| EN 12095-1997 |
Plastics piping systems - Brackets for rainwater piping systems - Test method for bracket strength |
| EN 12099-1997 |
Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content |
| EN 12100-1997 |
Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports |
| EN 12106-1997 |
Plastics piping systems - Polyethylene (PE) pipes - Test method for the resistance to internal pressure after application of squeeze-off |
| EN 12107-1997 |
Plastics piping systems - Injection-moulded thermoplastics fittings, valves and ancillary equipment - Determination of the long-term hydrostatic strength of thermoplastics materials for injection moulding of piping components |
| EN 12117-1997 |
Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships |
| EN 12118-1997 |
Plastics piping systems - Determination of moisture content in thermoplastics by coulometry |
| EN 12119-1997 |
Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to thermal cycling |
| EN 12200-1-2000 |
Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system |
| EN 12201-1-2003 |
Plastics piping systems for water supply - Polyethylene (PE) - Part 1: General |
| EN 12201-2-2003 |
Plastics piping systems for water supply - Polyethylene (PE) - Part 2: Pipes |
| EN 12201-3-2003 |
Plastics piping systems for water supply - Polyethylene (PE) - Part 3: Fittings |
| EN 12201-4-2001 |
Plastics piping systems for water supply - Polyethylene (PE) - Part 4: Valves |
| EN 12201-5-2003 |
Plastics piping systems for water supply - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 12220-1998 |
Ventilation for buildings - Ductwork - Dimensions of circular flanges for general ventilation |
| EN 12236-2002 |
Ventilation for buildings - Ductwork hangers and supports - Requirements for strength |
| EN 12237-2003 |
Ventilation for buildings - Ductwork - Strength and leakage of circular sheet metal ducts |
| EN 1225-1996 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the creep factor under wet conditions and calculation of the long-term specific ring stiffness |
| EN 12256-1998 |
Plastics piping systems - Thermoplastics fittings - Test method for mechanical strength or flexibility of fabricated fittings |
| EN 1226-1996 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method to prove the resistance to initial ring deflection |
| EN 1227-1997 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the long-term ultimate relative ring deflection under wet conditions |
| EN 1228-1996 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial specific ring stiffness |
| EN 1229-1996 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the leaktightness of the wall under short-term internal pressure |
| EN 12293-1999 |
Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of mounted assemblies to temperature cycling |
| EN 12294-1999 |
Plastics piping systems - Systems for hot and cold water - Test method for leaktightness under vacuum |
| EN 12295-1999 |
Plastics piping systems - Thermoplastics pipes and associated fittings for hot and cold water - Test method for resistance of joints to pressure cycling |
| EN 12308-1998 |
Installations and equipment for LNG - Suitability testing of gaskets designed for flanged joints used on LNG piping |
| EN 12474-2001 |
Cathodic protection of submarine pipelines |
| EN 12514-2-2000 |
Installations for oil supply systems for oil burners - Part 2: Safety requirements and tests - Parts, valves, pipes, filters, oil de-aerators, meters |
| EN 12585-1998 |
Glass plant, pipeline and fittings - Pipeline and fittings DN 15 to 1000 - Compatibility and interchangeability |
| EN 12735-1-2001 |
Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 1: Tubes for piping systems |
| EN 1277-1996 |
Plastics piping systems - Thermoplastics piping systems for buried non-pressure applications - Test methods for leaktightness of elastomeric sealing ring type joints |
| EN 12842-2000 |
Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods |
| EN 1295-1-1997 |
Structural design of buried pipelines under various conditions of loading - Part 1: General requirements |
| EN 12954-2001 |
Cathodic protection of buried or immersed metallic structures - General principles and application for pipelines |
| EN 13052-1-2001 |
Influence of materials on water intended for human consumption - Organic materials; Determination of colour and turbidity of water in piping systems - Part 1: Test method |
| EN 13090-2000 |
Means for resealing threaded joints of gas pipework in buildings |
| EN 13136-2001 |
Refrigerating systems and heat pumps - Pressure relief devices and their associated piping - Methods for calculation |
| EN 13180-2001 |
Ventilation for buildings - Ductwork - Dimensions and mechanical requirements for flexible ducts |
| EN 13220-1998 |
Flow-metering devices for connection to terminal units of medical gas pipeline systems |
| EN 13244-1-2002 |
Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage - Polyethylene (PE) - Part 1: General |
| EN 13244-2-2002 |
Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage - Polyethylene (PE) - Part 2: Pipes |
| EN 13244-3-2002 |
Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage - Polyethylene (PE) - Part 3: Fittings |
| EN 13244-4-2002 |
Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage - Polyethylene (PE) - Part 4: Valves |
| EN 13244-5-2002 |
Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 1329-1-1999 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system |
| EN 13312-1-2001 |
Biotechnology - Performance criteria for piping and instrumentation - Part 1: General performance criteria |
| EN 13312-2-2001 |
Biotechnology - Performance criteria for piping and instrumentation - Part 2: Couplings |
| EN 13312-3-2001 |
Biotechnology - Performance criteria for piping and instrumentation - Part 3: Sampling and inoculation devices |
| EN 13312-4-2001 |
Biotechnology - Performance criteria for piping and instrumentation - Part 4: Tubes and pipes |
| EN 13312-5-2001 |
Biotechnology - Performance criteria for piping and instrumentation - Part 5: Valves |
| EN 13312-6-2001 |
Biotechnology - Performance criteria for piping and instrumentation - Part 6: Equipment probes |
| EN 1333-1996 |
Pipework components - Definition and selection of PN |
| EN 13403-2003 |
Ventilation for buildings - Non-metallic ducts - Ductwork made from insulation ductboards |
| EN 13467-2001 |
Thermal insulating products for building equipment and industrial installations - Determination of dimensions, squareness and linearity of preformed pipe insulation |
| EN 13469-2001 |
Thermal insulating products for building equipment and industrial installations - Determination of water vapour transmission properties of preformed pipe insulation |
| EN 13470-2001 |
Thermal insulating products for building equipment and industrial installations - Determination of the apparent density of preformed pipe insulation |
| EN 13472-2001 |
Thermal insulating products for building equipment and industrial installations - Determination of short term water absorption by partial immersion of preformed pipe insulation |
| EN 13480-1-2002 |
Metallic industrial piping - Part 1: General |
| EN 13480-2-2002 |
Metallic industrial piping - Part 2: Materials |
| EN 13480-3-2002 |
Metallic industrial piping - Part 3: Design and calculation |
| EN 13480-4-2002 |
Metallic industrial piping - Part 4: Fabrication and installation |
| EN 13480-5-2002 |
Metallic industrial piping - Part 5: Inspection and testing |
| EN 13544-2-2002 |
Respiratory therapy equipment - Part 2: Tubing and connectors |
| EN 13566-1-2002 |
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 1: General |
| EN 13566-3-2002 |
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes |
| EN 13566-4-2002 |
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes |
| EN 13598-1-2003 |
Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings including shallow inspection chambers |
| EN 1366-1-1999 |
Fire resistance tests for service installations - Part 1: Ducts |
| EN 1366-5-2003 |
Fire resistance tests for service installations - Part 5: Service ducts and shafts |
| EN 13689-2002 |
Guidance on the classification and design of plastics piping systems used for renovation |
| EN 1393-1996+AC-1997 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial longitudinal tensile properties |
| EN 1394-1996+AC-1997 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the apparent initial circumferential tensile strength |
| EN 13942-2003 |
Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves (ISO 14313:1999, modified) |
| EN 1401-1-1998 |
Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system |
| EN 1411-1996 |
Plastics piping and ducting systems - Thermoplastics pipes - Determination of resistance to external blows by the staircase method |
| EN 14163-2001 |
Petroleum and natural gas industries - Pipeline transportation systems - Welding of pipelines (ISO 13847:2000, modified) |
| EN 1420-1-1999 |
Influence of organic materials on water intended for human consumption - Determination of odour and flavour assessment of water in piping systems - Part 1: Test method |
| EN 1437-2002 |
Plastics piping systems - Piping systems for underground drainage and sewerage - Test method for resistance to combined temperature cycling and external loading |
| EN 1444-2000 |
Fibre-cement pipelines - Guide for laying and on-site work practices |
| EN 1446-1996 |
Plastics piping and ducting systems - Thermoplastics pipes - Determination of ring flexibility |
| EN 1447-1996 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of long-term resistance to internal pressure |
| EN 1448-1996 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) components - Test methods to prove the design of rigid locked socket-and-spigot joints with elastomeric seals |
| EN 1449-1996 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) components - Test methods to prove the design of cemented socket-and-spigot joints |
| EN 1450-1996+A1-1998 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) components - Test methods to prove the design of bolted flange joints |
| EN 1451-1-1998 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system |
| EN 1452-1-1999 |
Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: General |
| EN 1452-2-1999 |
Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Pipes |
| EN 1452-3-1999 |
Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Fittings |
| EN 1452-4-1999 |
Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves and ancillary equipment |
| EN 1452-5-1999 |
Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 5: Fitness for purpose of the system |
| EN 1453-1-2000 |
Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes and the system |
| EN 1455-1-1999 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Requirements for pipes, fittings and the system |
| EN 1456-1-2001 |
Plastics piping systems for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for piping components and the system |
| EN 1505-1997 |
Ventilation for buildings - Sheet metal air ducts and fittings with rectangular cross section - Dimensions |
| EN 1506-1997 |
Ventilation for buildings - Sheet metal air ducts and fittings with circular cross-section - Dimensions |
| EN 1519-1-1999 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system |
| EN 1555-1-2002 |
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General |
| EN 1555-2-2002 |
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes |
| EN 1555-3-2002 |
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings |
| EN 1555-4-2002 |
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4: Valves |
| EN 1555-5-2002 |
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 1565-1-1998 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 1: Specifications for pipes, fittings and the system |
| EN 1566-1-1998 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system |
| EN 1594-2000 |
Gas supply systems - Pipelines for maximum operating pressure over 16 bar - Functional requirements |
| EN 1636-3-1997 |
Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 3: Fittings |
| EN 1636-5-1997 |
Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 5: Fitness for purpose of the joints |
| EN 1636-6-1997 |
Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 6: Practices for installation |
| EN 1638-1997 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method for the effects of cyclic internal pressure |
| EN 1680-1997 |
Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanism |
| EN 1704-1997 |
Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after temperature cycling under bending |
| EN 1705-1996 |
Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow |
| EN 1716-1997 |
Plastics piping systems - Polyethylene (PE) tapping tees - Test method for impact resistance of an assembled tapping tee |
| EN 1775-1998+A1 -2000+A2-2000 |
Gas supply - Gas pipework for buildings - Maximum operating pressure 5 bar - Functional recommendations |
| EN 1852-1-1997+A1-2001 |
Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system |
| EN 1861-1998 |
Refrigerating systems and heat pumps - System flow diagrams and piping and instrument diagrams - Layout and symbols |
| EN 1862-1997 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the relative flexural creep factor following exposure to a chemical environment |
| EN 187105-2002 |
Single mode optical cable (duct/direct buried installation) |
| EN 1905-1998 |
Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material - Method for assessment of the PVC content based on total chlorine content |
| EN 1979-1999 |
Plastics piping and ducting systems - Thermoplastics spirally-formed structured-wall pipes - Determination of the tensile strength of a seam |
| EN 1989-2000 |
Thermoplastics piping systems - Joints for buried non-pressure sewerage applications - Test method for long-term sealing performance of joints with thermoplastic elastomer (TPE) seals by estimating the sealing pressure |
| EN 24006-1993 |
Measurement of fluid flow in closed conduits; vocabulary and symbols (ISO 4006:1991) |
| EN 24185-1993 |
Measurement of liquid flow in closed conduits; Weighing method (ISO 4185:1980) |
| EN 253-2003 |
District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene |
| EN 288-9-1999 |
Specification and approval of welding procedures for metallic materials - Part 9: Welding procedure test for pipeline welding on land and offshore site butt welding of transmission pipelines |
| EN 29104-1993 |
Measurement of fluid flow in closed conduits; methods of evaluating the performance of electromagnetic flow-meters for liquids (ISO 9104:1991) |
| EN 4028-2001 |
Aerospace series - Pipe coupling 8?0 in titanium alloy - Tees with thrust wire nut on run |
| EN 4030-2001 |
Aerospace series - Pipe coupling 8?0 in titanium alloy - Tees bulkhead on run |
| EN 4190-2001 |
Aerospace series - Pipe coupling 8 Degree 30′in titanium alloy - Tees, reduced with thrust wire nut on run |
| EN 448-2003 |
District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| EN 45510-7-1-1999 |
Guide for procurement of power station plant, equipment, and systems - Part 7-1: Pipework and valves - High pressure piping systems |
| EN 45510-7-2-1999 |
Guide for procurement of power station plant, equipment, and systems - Part 7-2: Pipework and valves - Boiler and high pressure piping valves |
| EN 474-9-1998 |
Earth-moving machinery - Safety - Part 9: Requirements for pipelayers |
| EN 476-1997 |
General requirements for components used in discharge pipes, drains and sewers for gravity systems |
| EN 488-2003 |
District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| EN 489-2003 |
District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| EN 50085-1-1997+A1-1998 |
Cable trunking systems and cable ducting systems for electrical installations - Part 1: General requirements |
| EN 50085-1/prA2-2002 |
Cable trunking systems and cable ducting systems for electrical installations - Part 1: General requirements; Amendment A2 |
| EN 50085-2-3-1999 |
Cable trunking systems and cable ducting systems for electrical installations - Part 2-3: Particular requirements for slotted cable trunking systems intended for installation in cabinets |
| EN 50249-2002 |
Electromagnetic locators for buried pipes and cables - Performance and safety |
| EN 512-1994+A1-2001 |
Fibre-cement products - Pressure pipes and joints |
| EN 545-2002 |
Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods |
| EN 578-1993 |
Plastics piping systems - Plastics pipes and fittings - Determination of the opacity |
| EN 579-1993 |
Plastics piping systems - rosslinked polyethylene (PE-X) pipes -Determination of degree of crosslinking by solvent extraction |
| EN 580-2003 |
Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for the resistance to dichloromethane at a specified temperature (DCMT) |
| EN 588-1-1996 |
Fibre-cement pipes for sewers and drains - Part 1: Pipes, joints and fittings for gravity systems |
| EN 60794-3-10-2002 |
Optical fibre cables - Part 3-10: Outdoor cables; Family specification for duct and directly buried optical telecommunication cables (IEC 60794-3-10:2002, modified) / Note: Endorsement notice |
| EN 637-1994 |
Plastics piping systems - Glass-reinforced plastics components - Determination of the amounts of constituents using the gravimetric method |
| EN 681-1-1996+A1-1998 +A2-2002+AC-2002 |
Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber |
| EN 681-2-2000+A1-2002 |
Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers |
| EN 681-3-2000+A1-2002 |
Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 3: Cellular materials of vulcanized rubber |
| EN 681-4-2000+A1-2002 |
Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 4: Cast polyurethane sealing elements |
| EN 682-2002 |
Elastomeric seals - Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids |
| EN 705-1994 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Methods for regression analysis and their use |
| EN 712-1993 |
Thermoplastics piping systems - End-load bearing mechanical joints between pressure pipes and fittings - Test method for resistance to pull-out under constant longitudinal force |
| EN 713-1993 |
Plastic piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending |
| EN 714-1994 |
Thermoplastics piping systems - Non-end-load-bearing elastomeric sealing ring type joints between pressure pipes and moulded fittings - Test method for leaktightness under internal hydrostatic pressure without end thrust |
| EN 715-1994 |
Thermoplastics piping systems - End-load bearing joints between small diameter pressure pipes and fittings-Test method for leaktightness under internal water pressure, including end thrust |
| EN 727-1994 |
Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST) |
| EN 728-1997 |
Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time |
| EN 737-1-1998 |
Medical gas pipeline systems - Part 1: Terminal units for compressed medical gases and vacuum |
| EN 737-2-1998+A1 -1999+AC-2000 |
Medical gas pipeline systems - Part 2: Anaesthetic gas scavenging disposal systems - Basic requirements |
| EN 737-3-1998+A1 -1999+AC-2000 |
Medical gas pipeline systems - Part 3: Pipelines for compressed medical gases and vacuum |
| EN 737-4-1998 |
Medical gas pipeline systems - Part 4: Terminal units for anaesthetic gas scavenging systems |
| EN 743-1994 |
Plastic piping and ducting systems -Thermoplastics pipes -Determination of the longitudinal reversion |
| EN 744-1995 |
Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock method |
| EN 761-1994 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the creep factor under dry conditions |
| EN 763-1994 |
Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Test method for visually assessing effects of heating |
| EN 802-1994 |
Plastics piping and ducting systems - Injection-moulded thermoplastics fittings for pressure piping systems - Test method for maximum deformation by crushing |
| EN 803-1994 |
Plastics piping systems - Injection-moulded thermoplastics fittings for elastic sealing ring type joints for pressure piping - Test method for resistance to a short-term internal pressure without end thrust |
| EN 804-1994 |
Plastics piping systems - Injection-moulded socket fittings for solvent-cemented joints for pressure piping - Test method for resistance to a short-term internal hydrostatic pressure |
| EN 911-1995 |
Plastics piping systems - Elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping - Test method for leaktightness under external hydrostatic pressure |
| EN 921-1994+AC-1995 |
Plastics piping systems - Thermoplastics pipes - Determination of resistance to internal pressure at constant temperature / Note: To be replaced by prEN ISO 1167-1 (2003-04), prEN ISO 1167-2 (2003-04). |
| EN 922-1994 |
Plastics piping and ducting systems - Pipes and fittings of unplasticized poly(vinyl chloride) (PVC-U) - Specimen preparation for determination of the viscosity number and calculation of the K-value |
| EN 969-1995+A1-1998 |
Ductile iron pipes, fittings, accessories and their joints for gas pipelines - Requirements and test methods |
| EN ISO 10380-2003 |
Pipework - Corrugated metal hoses and hose assemblies (ISO 10380:2003) |
| EN ISO 10472-3-1997 |
Safety requirements for industrial laundry machinery - Part 3: Washing tunnel lines including component machines (ISO 10472-3:1997) |
| EN ISO 10807-1996 |
Pipework - Corrugated flexible metallic hose assemblies for the protection of electrical cables in explosive atmosphere (ISO 10807:1994) |
| EN ISO 11691-1995 |
Acoustics - Measurement of insertion loss of ducted silencers without flow - Laboratory survey method (ISO 11691:1995) |
| EN ISO 13703-2000 |
Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms (ISO 13703:2000) |
| EN ISO 13783-1997 |
Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double socket joints - Test method for leaktightness and strength while subjected to bending and internal pressure (ISO 13783:1997) |
| EN ISO 13844-2000 |
Plastics piping systems - Elastomeric-sealing-ring-type socket joints of unplasticized poly(vinyl chloride) (PVC-U) for use with PVC-U pipes - Test method for leaktightness under negative pressure (ISO 13844:2000) |
| EN ISO 13845-2000 |
Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for leaktightness under internal pressure and with angular deflection (ISO 13845:2000) |
| EN ISO 13846-2000 |
Plastics piping systems - End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping - Test method for long-term leaktightness under internal water pressure (ISO 13846:2000) |
| EN ISO 14723-2001 |
Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves (ISO 14723:2001) |
| EN ISO 15493-2003 |
Plastics piping systems for industrial applications - Acrylonitrile-butadiene-styrene (ABS), unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) - Specificatio |
| EN ISO 15494-2003 |
Plastics piping systems for industrial applications - Polybutene (PB), polyethylene (PE) and polypropylene (PP) - Specifications for components and the system; Metric series (ISO 15494:2003) |
| EN ISO 15908-2002 |
Adhesives for thermoplastic piping systems - Test method for the determination of thermal stability of adhesives (ISO 15908:2002) |
| EN ISO 16871-2003 |
Plastics piping and ducting systems - Plastics pipes and fittings - Method for exposure to direct (natural) weathering (ISO 16871:2003) |
| EN ISO 5136-2003 |
Acoustics - Determination of sound power radiated into a duct by fans and other air-moving devices - In-duct method (ISO 5136:2003) |
| EN ISO 5167-1-2003 |
Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003) |
| EN ISO 5167-2-2003 |
Measurement of fluid flow by means of pressure differential devices in circular cross-section conduits running full - Part 2: Orifice plates (ISO 5167-2:2003) |
| EN ISO 5167-3-2003 |
Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles (ISO 5167-3:2003) |
| EN ISO 5167-4-2003 |
Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 4: Venturi tubes (ISO 5167-4:2003) |
| EN ISO 6412-1-1994 |
Technical drawings - Simplified representation of pipelines - Part 1: General rules and orthogonal representation (ISO 6412-1:1989) |
| EN ISO 6412-2-1994 |
Technical drawings - Simplified representation of pipelines - Part 2: Isometric projection (ISO 6412-2:1989) |
| EN ISO 6412-3-1996 |
Technical drawings - Simplified representation of pipelines - Part 3: Terminal features of ventilation and drainage systems (ISO 6412-3:1993) |
| EN ISO 6817-1995 |
Measurement of conductive liquid flow in closed conduits - Method using electromagnetic flowmeters (ISO 6817:1992) |
| EN ISO 7235-2003 |
Acoustics - Laboratory measurement procedures for ducted silencers and air-terminal units - Insertion loss, flow noise and total pressure loss (ISO 7235:2003) |
| EN ISO 7278-2-1995 |
Liquid hydrocarbons - Dynamic measurement - Proving systems for volumetric meters - Part 2: Pipe provers (ISO 7278-2:1988) |
| EN ISO 8316-1995 |
Measurement of liquid flow in closed conduits - Method by collection of the liquid in a volumetric tank (ISO 8316:1987) |
| EN ISO 8795-2001 |
Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Determination of migration values of plastics pipes and fittings and their joints (ISO 8795:2001) |
| EN ISO 9080-2003 |
Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2003) |
| ENV 1046-2001 |
Plastics piping and ducting systems - Systems outside building structures for the conveyance of water or sewage - Practices for installation above and below ground |
| ENV 12097-1997 |
Ventilation for buildings - Ductwork - Requirements for ductwork components to facilitate maintenance of ductwork systems |
| ENV 12108-2001 |
Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption |
| ENV 1329-2-2001 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity |
| ENV 13801-2000 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Thermoplastics - Recommended practice for installation |
| ENV 1401-2-2000 |
Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for assessment of conformity |
| ENV 1401-3-2001 |
Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Guidance for installation |
| ENV 1451-2-2001 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity |
| ENV 1452-6-2001 |
Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 6: Guidance for installation |
| ENV 1452-7-2000 |
Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 7: Guidance for the assessment of conformity |
| ENV 1453-2-2000 |
Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity |
| ENV 1455-2-2001 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 2: Guidance for the assessment of conformity |
| ENV 1519-2-2001 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 2: Guidance for the assessment of conformity |
| ENV 1565-2-2001 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 2: Guidance for the assessment of conformity |
| ENV 1566-2-2001 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly (vinyl chloride) (PVC-C) - Part 2: Guidance for the assessment of conformity |
| ENV 1852-2-2000 |
Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity |
| ENV 1993-4-1-1999 |
Eurocode 3: Design of steel structures - Part 4-1: Silos, tanks and pipelines - Silos |
| ENV 1993-4-2-1999 |
Eurocode 3: Design of steel structures - Part 4-2: Silos, tanks and pipelines - Tanks |
| ENV 1993-4-3-1999 |
Eurocode 3: Design of steel structures - Part 4-3: Silos, tanks and pipelines - Pipelines |
| ENV 1998-4-1998 |
Eurocode 8: Design provisions for earthquake resistance of structures - Part 4: Silos, tanks and pipelines |
| ENV 737-6-2003 |
Medical gas pipeline systems - Part 6: Dimensions and allocation of probes for terminal units for compressed medical gases and vacuum |
| ENV 852-2001 |
Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Guidance on the interpretation of laboratory derived migration values |
| prEN 1016-1993 |
Plastics piping systems; unplasticized poly(vinyl chloride) (PVC-U) end-load bearing double socket joints; test method for leaktightness and strength while subjected to bending and internal pressure |
| prEN 10208-3-1997 |
Steel pipes for pipelines for combustible fluids - Technical delivery conditions - Part 3: Pipes of requirement class C |
| prEN 1042-1995 |
Plastics piping systems - Fusion joints between polyolefin pipes and/or fittings - Determination of resistance to internal pressure at constant temperature |
| prEN 1115-2-1997 |
Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 2: Pipes with flexible, reduced articulation or rigid joints |
| prEN 1115-4-1993 |
Plastics piping systems for underground drainage and sewerage under pressure; glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP); part 4 (informative): ancillary equipment |
| prEN 1115-6-1997 |
Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 6: Practices for installation |
| prEN 1115-7-1995 |
Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 7: Assessment of conformity |
| prEN 12666-1-2001 |
Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system |
| prEN 1329-3-1998 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Guidance for installation |
| prEN 1329-5-1994 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure; unplasticized poly(vinyl chloride) (PVC-U); part 5: fitness for purpose of the system |
| prEN 1329-6-1994 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 6: Recommended practice for installation |
| prEN 1336-1993 |
Plastics piping systems; end-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping; test method for long-term leaktightness under internal water pressure |
| prEN 13476-1-2002 |
Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for pipes, fittings and the syste |
| prEN 13480-6-2002 |
Metallic industrial piping - Part 6: Additional requirements for buried piping |
| prEN 13566-2-2002 |
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes |
| prEN 13636-2003 |
Cathodic protection of buried metallic tanks and related piping |
| prEN 1401-5-1994 |
Plastics piping systems for non-pressure underground drainage and sewerage; unplasticized poly(vinyl chloride) (PVC-U); part 5: fitness for purpose of the system |
| prEN 14125-2003 |
Pipework for underground installation at petrol stations |
| prEN 14141-2003 |
Valves for natural gas transportation in pipelines - Performance requirements and tests |
| prEN 14161-2003 |
Petroleum and natural gas industries - Pipeline transportation systems (ISO 13623:2000 modified) |
| prEN 14239-2003 |
Ventilation for buildings - Ductwork - Measurement of ductwork surface area |
| prEN 14280-2001 |
Plastics piping systems for buried cable ducting - Unplasticized poly(vinyl chloride) (PVC-U) - Specifications for pipes, fittings and the system |
| prEN 14281-2001 |
Plastics piping systems for buried cable ducting - Polyethylene (PE) - Specifications for pipes, fittings and the system |
| prEN 14282-2001 |
Plastics piping systems for buried cable ducting - Polypropylene (PP) - Specifications for pipes, fittings and the system |
| prEN 14283-2001 |
Plastics piping systems for general purpose buried ducting - Unplasticized poly(vinyl chloride) (PVC-U) - Specifications for pipes, fittings and the system |
| prEN 14284-2001 |
Plastics piping systems for general purpose buried ducting - Polyethylene (PE) - Specifications for pipes, fittings and the system |
| prEN 14285-2001 |
Plastics piping systems for general purpose buried ducting - Polypropylene (PP) - Specifications for pipes, fittings and the system |
| prEN 1445-2000 |
Fibre-cement pipelines - Field pressure testing |
| prEN 1451-3-1994 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 3: Fittings |
| prEN 1451-5-1994 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 5: Fitness for purpose of the system |
| prEN 1451-6-1994 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building - Polypropylene (PP) - Part 6: Recommended practice for installation |
| prEN 1453-3-1998 |
Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Guidance for installation |
| prEN 1453-5-1994 |
Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) within the building structure; unplasticized poly(vinyl chloride) (PVC-U); part 5: fittings for purpose of the system |
| prEN 1453-6-1994 |
Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) within the building structure; unplasticized poly(vinyl chloride) (PVC-U); part 6: recommended practice for installation |
| prEN 1455-3-1994 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 3: Fittings |
| prEN 1455-6-1994 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building - Acrylonitrile-butadiene-styrene (ABS) - Part 6: Recommended practice for installation |
| prEN 1456-3-1994 |
Plastics piping systems for underground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Fittings |
| prEN 1456-4-1994 |
Plastics piping systems for underground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves and ancillary equipment |
| prEN 1456-5-1994 |
Plastics piping systems for underground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 5: Fitness for purpose of the system |
| prEN 1456-6-1994 |
Plastics piping systems for underground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 6: Recommended practice for installation |
| prEN 1507-2002 |
Ventilation for buildings - Sheet metal air ducts with rectangular section - Requirements for strength and leakage |
| prEN 1519-3-1994 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 3: Fittings |
| prEN 1519-5-1994 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| prEN 1519-6-1995 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 6: Recommanded practice for installation |
| prEN 1555-6-1995 |
Plastics piping systems for gaseous fuels supply - Polyethylene (PE) - Part 6: Recommended practice for installation |
| prEN 1565-3-1994 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 3: Fittings |
| prEN 1565-5-1994 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 5: Fitness for purpose of the system |
| prEN 1565-6-1995 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN + PVC) - Part 6: Recommended practice for installation |
| prEN 1566-3-1994 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings |
| prEN 1566-5-1994 |
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system |
| prEN 1636-1-1996 |
Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 1: General |
| prEN 1636-2-1996 |
Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 2: Pipes with flexible, reduced articulation or rigid joints |
| prEN 1636-4-1994 |
Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 4: Ancillary equipment |
| prEN 1763-2-2000 |
Flexible hose, tubing and assemblies for use with propane and butane in the vapour phase - Part 2: Requirements for nozzles, couplings and assemblies |
| prEN 1796-2-1995 |
Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 2: Pipes with flexible, reduced articulation or rigid joints |
| prEN 1796-2003 |
Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) |
| prEN 1796-3-1995 |
Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 3: Fittings |
| prEN 1796-4-1995 |
Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 4: Ancillary equipment |
| prEN 1796-5-1995 |
Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 5: Fitness for the purpose of the system |
| prEN 1796-6-1995 |
Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 6: Recommended practice for installation |
| prEN 1852-5-1995 |
Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 5: Fitness for purpose of the system |
| prEN 45512-1994 |
Guide for procurement - Pipework and valves - Boiler and high pressure piping valves including safety valves |
| prEN 45513-1994 |
Guide for procurement - Pipework and valves - High pressure piping including supports |
| prEN 474-9-2001 |
Earth-moving machinery - Safety - Part 9: Requirements for pipelayers |
| prEN 50085-2-1-2002 |
Cable trunking and cable ducting systems for electrical installations - Part 2-1: Particular requirements for cable trunking systems and cable ducting systems intended for mounting on walls and/or ceilings |
| prEN 762-1995 |
Plastics piping and ducting systems - Joints with elastomeric seals for thermoplastic systems - Test method for retention of, and damage to, sealing rings |
| prEN 806-3-2003 |
Specifications for installations inside buildings conveying water for human consumption - Part 3: Pipe sizing |
| prEN 987-1995 |
Plastics piping and ducting systems - Injection-moulded fittings - Determination of the Charpy impact strength of test pieces cut from a fitting |
| prEN ISO 10806-2003 |
Pipework - Fittings for corrugated metallic hoses (ISO/FDIS 10806:2003) |
| prEN ISO 14828-1999 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the long-term specific ring relaxation stiffness under wet conditions and calculation of the wet relaxation factor (ISO/DIS 14828:1999) |
| prEN ISO 15002-1996 |
Flow-metering devices for connection to terminal units of medical gas pipeline systems (ISO/DIS 15002:1996) |
| prEN ISO 15465-2002 |
Pipework - Stripwound metal hoses and hose assemblies (ISO/DIS 15465:2002) |
| prEN ISO 15749-2-2001 |
Ships and marine technology - Drainage systems on ships and marine structures - Part 2: Sanitary drainage, drain piping for gravity system (ISO/DIS 15749-2:2001) |
| prEN ISO 15749-4-2001 |
Ships and marine technology - Drainage systems on ships and marine structures - Part 4: Sanitary drainage, sewage disposal pipes (ISO/DIS 15749-4:2001) |
| prEN ISO 15874-1-2002 |
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General (ISO/FDIS 15874-1:2002) |
| prEN ISO 15874-2-2002 |
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes (ISO/FDIS 15874-2:2002) |
| prEN ISO 15874-3-2002 |
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings (ISO/FDIS 15874-3:2002) |
| prEN ISO 15874-5-2002 |
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 5: Fitness for purpose of the system (ISO/FDIS 15874-5:2002) |
| prEN ISO 15875-1-2002 |
Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 1: General (ISO/FDIS 15875-1:2002) |
| prEN ISO 15875-2-2002 |
Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 2: Pipes (ISO/FDIS 15875-2:2002) |
| prEN ISO 15875-3-2002 |
Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings (ISO/FDIS 15875-3:2002) |
| prEN ISO 15875-5-2002 |
Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system (ISO/FDIS 15875-5:2002) |
| prEN ISO 15876-1-2002 |
Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 1: General (ISO/FDIS 15876-1:2002) |
| prEN ISO 15876-2-2002 |
Plastics piping systems for hot and cold water installations - Polybutylen (PB) - Part 2: Pipes (ISO/FDIS 15876-2:2002) |
| prEN ISO 15876-3-2002 |
Plastics piping systems for hot and cold water installations - Polybutylen (PB) - Part 3: Fittings (ISO/FDIS 15876-3:2002) |
| prEN ISO 15876-5-2002 |
Plastics piping systems for hot and cold water installations - Polybutylen (PB) - Part 5: Fittness for purpose of the system (ISO/FDIS 15876-5:2002) |
| prEN ISO 15877-1-2002 |
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: General (ISO/FDIS 15877-1:2002) |
| prEN ISO 15877-2-2002 |
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes (ISO/FDIS 15877-2:2002) |
| prEN ISO 15877-3-2002 |
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings (ISO/FDIS 15877-3:2002) |
| prEN ISO 15877-5-2002 |
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system (ISO/FDIS 15877-5:2002) |
| prEN ISO 580-2002 |
Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO/DIS 580:2002) |
| prEN ISO 7369-2002 |
Pipework - Metal hoses and hose assemblies - Vocabulary (ISO/DIS 7369:2002) |
Mail consultation
Please feel free to give your inquiry in the form below.We will reply you in 24 hours.
News List
feature product
Contact Us