• Alloy steel pipe
  • Ductile Iron Pipe
  • Carbon Steel Pipe
  • OCTG Steel Pipe
  • Stainless Steel Pipe
Product
contact us

Address:Beijing Road, Yunhe District, Shengji Building #1802 ,Cangzhou City, Hebei

Contact:Lucky

Phone:86-15003171886

E-mail:jinxiaolong0221@gmail.com
         beitesteelpipe@gmail.com


  • JIS G3460 STPL450 STPL690 Steel Tubes
Title:
Tel:
E-mail: *
Content: *
Verification Code:
 

  • JIS G3460 STPL450 STPL690 Seamless Steel Tubes
     
     
    Steel tubes for low temperature service
     
     
     
    JIS G3460 STPL380 STPL690 Steel tubes usually applies to pipes with an outer diameter of 10.5 mm to 660.4 mm,used at particularly low temperature below freezing.

     
     
    JIS G3460 STPL380 STPL690 Steel Tubes Quick Details
    Manufacturing:Seamless; Electric resistance welding
    Type:Hot finished,Cold finished,welded.
    Wall thickness(WT): 12.7mm——50 mm.
    Outer diameter (OD): 10.5mm——660.4mm
    Length: 6M or specified length as required.
    Ends: Plain End, Beveled End, Treaded
     
     
    Additional Info
    Port of Shipment: Tianjin, China
    Payment Terms:T / T, LC
    Delivery: 7-15 days after payment
    Surface: Tubes will be varnished (Outside only) to prevent rust.
    Marking: Standard + Steel Grade + Size + Heat No + Lot No
    Package:Standard export package,suit for all kinds of transport, or as required
     


     
    Manufacturing method of JIS G3460 STPL380 STPL690
    (1)The tube is made of fine-grained killed steel, STPL 450 and STPL 690 are manufactured seamlessly.
    (2)The pipe is heat-treated in Table 1. However, when performing heat treatments other than those in Table 1, it is based on the agreement between the delivery parties. Cold-finished tubes are heat-treated after cold-finishing.
    Table 1-Heat treatment
     
    Grade Heat treatment
    STPL450 Normalized, Normalized, Post-tempered,
    Or quenching and tempering
    STPL690 Post-tempered normalizing or tempering or tempering
     

    c) The end of the pipe is plain end unless otherwise specified. If the orderer specifies a bevel end, the shape shall be in accordance with the agreement between the delivering and receiving parties, in particular when no shape is specified, according to Figure 1.
     

     

    t: Thickness 22 mm or less
    Figure 1-Shape of bevel end



     
    Chemical composition of JIS G3460 STPL380 STPL690

    Letter symbol of grade
    Chemical Composition %
    C Si Mn P S Ni
    STPL 450 0.18 max. 0.10~0.35 0.30~0.60 0.030 max. 0.030 max. 3.20 ~ 3.80
    STPL 690 0.13 max. 0.10~0.35 0.90 max. 0.030 max. 0.030 max. 8.50 ~ 9.50
     

     
    Mechanical properties of JIS G3460 STPL380 STPL690
     
    Letter symbol of grade Mechanical properties
    Tensile strength Yield point or proof stress Elongation %
    kgf/mm2 {N/mm2} kgf/mm2 {N/mm2} No. 11 or No. 12 test piece No. 5 test piece No. 4 test piece
    Longitudinal Transverse Longitudinal Transverse
    STPL 450 46{451}min 25{245} min. 30 min. 20 min. 24 min. 16 min.
    STPL 690 70{686}min 53{520} min. 21 min. 15 min. 16 min. 10 min.
     
    Note 1N / mm2 = 1 MPa
    Note) For tubes with an outside diameter of less than 40 mm, the elongation in this table does not apply.
     


    Dimensional tolerances
     
    Tolerances on Outside Diameter, Wall Thickness and Deviation in Wall Thickness
     

    Division Tolerance on outside diameter Tolerance on wall
    thickness
    Tolerances on deviation in wall thickness
    Hot-finished seamless steel pipe Up to 50 mm 【 0.5mm Up to 4mm【0.5mm Within 20% of wall thickness
    50mm or over,【1%
    up to 160mm
    4mm and over【12.5%
    160mm and over,【1.6mm up to 200mm
    200mm or over 【 0.8%
    However, for pipes 350mm or over in diameter, the length of circumference may be used as a bases for tolerance. In this case, the tolerances shall be 【 0.5%
    Cold-finished seamless steel pipe, electric-resistance welded pipe Up to 40mm 【 0.3mm Up to 2mm【0.2mm  
     
     
    -
    40mm and over 【 0.8%  
    2mm and over【10%
    However, for pipes 350mm or over in diameter, the length of circumference may be used as a bases for tolerances. In this case, the tolerance shall be 【 0.5 %

     
     
    Appearance
    a) tube must be practical and straight and both ends are perpendicular to the tube axis.
    b) the inner surface of the tube is good in finishing, and there is no defect which is harmful to use.
    c) in the case of surface treatment, it may be necessary for grindstone or machining, but the thickness of the product after the care must be within the tolerance of thickness.
    d) the ruins must be smoothly formed in the shape of the tube.
     
     
     
    Testings
    Analysis testing
    Mechanical testing
    Tensile testing
    Flattening testing
    Bending testing
    Charpy impact testing
    Hydraulic or non-destructive testing
     


    Marking
    a) type of symbol
    b) a symbol representing a manufacturing method
    The symbols representing the manufacturing method are as follows. However,-may be blank.
    1) Hot finish seamless steel pipe -S-H
    2) Cold finish seamless steel pipe -S-C
    3) Electric resistance welded as-is steel pipe -E-G
    4) Hot finish electric resistance welded steel pipe -E-H
    5) Cold finish electric resistance welded steel pipe -EC
     
    c) Dimensions. The dimensions indicate the nominal diameter and nominal thickness, or the outer diameter and thickness.
    Example 50A × Sch40 or 60.5 × 3.9
    d) Manufacturer name or its code
    e) Symbol Z representing designation of special quality regulations (when designated)


     
    Report

    We will submit inspection documents to the order.




    We are a professional JIS G3460 Steel Tubes supplier, if you want to know the details of JIS G3460 Steel Tubes, please contact us Email:jinxiaolong0221@gmail.com

     

    HOME |  Company |  Product |  News |  KnowLedge |  Equipment |  Contact | 

    Technical Support:CZWLWL.COM  Address:Beijing Road, Yunhe District, Shengji Building #1802 ,Cangzhou City, Hebei

    Phone:86-15003171886   站长流量统计